HAS 200-P Hall Effect Current Sensor - Equivalent & Substitute Parts

Part Overview

The HAS 200-P is a Hall Effect open-loop bidirectional current sensor manufactured by LEM USA Inc., designed for AC/DC current measurement applications up to 200A. This module provides ratiometric voltage output with ±1% linearity and accuracy across a frequency range of DC to 50kHz. The part is classified as Active product status and is RoHS compliant with REACH unaffected designation. Alternative models within the HAS series are available to accommodate different current measurement ranges and packaging specifications, allowing for design flexibility and supply chain optimization.

Key Parameters

Parameter	Value
Manufacturer Part Number	HAS 200-P
Manufacturer	LEM USA Inc.
Series	HAS
Product Status	Active
Sensor Type	Hall Effect, Open Loop
Current - Sensing	200A
Number of Channels	1
Output Type	Ratiometric, Voltage
Frequency Range	DC ~ 50kHz
Linearity	±1%
Accuracy	±1%
Voltage - Supply	±15V
Response Time	3µs
Current - Supply (Max)	15mA
Operating Temperature	-10°C ~ 80°C
Polarization	Bidirectional
Mounting Type	Through Hole
Package / Case	Module
Packaging	Tray
RoHS Status	RoHS Compliant
Moisture Sensitivity Level (MSL)	1 (Unlimited)
REACH Status	REACH Unaffected

Substitute Part Grouping Explanation

Substitution within the HAS series is determined by the following critical parameters:

Current Sensing Range: The primary differentiator among HAS series sensors. The HAS 200-P measures up to 200A. Substitute models include HAS 100-P, HAS 100-S, HAS 50-P, and HAS 50-S with lower current ratings, and HAS 200-S with identical current rating.

Packaging Variant: The HAS series uses suffix designations to indicate packaging type. The "-P" suffix indicates Tray packaging with MSL 1 (Unlimited). The "-S" suffix indicates alternative packaging with MSL Not Applicable.

Product Status: HAS 200-P and HAS 200-S maintain Active status. HAS 50-P is marked Not For New Designs. HAS 100-P, HAS 100-S, and HAS 50-S are Active.

Common Electrical Characteristics: All substitute parts share identical specifications for output type (Ratiometric, Voltage), frequency range (DC ~ 50kHz), linearity (±1%), accuracy (±1%), supply voltage (±15V), response time (3µs), maximum supply current (15mA), operating temperature (-10°C ~ 80°C), polarization (Bidirectional), and mounting type (Through Hole).

Compliance & Certifications: All parts are RoHS Compliant, REACH Unaffected, and carry identical ECCN (EAR99) and HTSUS (9030.33.3800) classifications.

Parameter Comparison

Parameter	HAS 200-P	HAS 200-S	HAS 100-P	HAS 100-S	HAS 50-P	HAS 50-S
Current - Sensing	200A	200A	100A	100A	50A	50A
Product Status	Active	Active	Active	Active	Not For New Designs	Active
Packaging	Tray	Tray	Tray	Tray	Tray	Tray
MSL	1 (Unlimited)	Not Applicable	1 (Unlimited)	Not Applicable	1 (Unlimited)	Not Applicable
Output Type	Ratiometric, Voltage	Ratiometric, Voltage	Ratiometric, Voltage	Ratiometric, Voltage	Ratiometric, Voltage	Ratiometric, Voltage
Frequency Range	DC ~ 50kHz	DC ~ 50kHz	DC ~ 50kHz	DC ~ 50kHz	DC ~ 50kHz	DC ~ 50kHz
Linearity	±1%	±1%	±1%	±1%	±1%	±1%
Accuracy	±1%	±1%	±1%	±1%	±1%	±1%
Voltage - Supply	±15V	±15V	±15V	±15V	±15V	±15V
Response Time	3µs	3µs	3µs	3µs	3µs	3µs
Current - Supply (Max)	15mA	15mA	15mA	15mA	15mA	15mA
Operating Temperature	-10°C ~ 80°C	-10°C ~ 80°C	-10°C ~ 80°C	-10°C ~ 80°C	-10°C ~ 80°C	-10°C ~ 80°C
Polarization	Bidirectional	Bidirectional	Bidirectional	Bidirectional	Bidirectional	Bidirectional
Mounting Type	Through Hole	Through Hole	Through Hole	Through Hole	Through Hole	Through Hole
RoHS Status	RoHS Compliant	RoHS Compliant	RoHS Compliant	RoHS Compliant	RoHS Compliant	RoHS Compliant
REACH Status	REACH Unaffected	REACH Unaffected	REACH Unaffected	REACH Unaffected	REACH Unaffected	REACH Unaffected

Engineering Selection Recommendations

Direct Equivalent (Same Current Rating)

HAS 200-S is the direct equivalent to HAS 200-P. Both sensors measure 200A with identical electrical performance characteristics. The primary distinction is the MSL designation: HAS 200-P carries MSL 1 (Unlimited), while HAS 200-S carries MSL Not Applicable. Both maintain Active product status and RoHS compliance. Selection between these two depends on moisture sensitivity requirements for your specific assembly process and storage conditions.

Lower Current Range Alternatives

HAS 100-P and HAS 100-S are suitable for applications requiring 100A measurement capacity. These sensors maintain all electrical specifications identical to the HAS 200-P except for the reduced current sensing range. HAS 100-P (Active status, MSL 1 Unlimited) and HAS 100-S (Active status, MSL Not Applicable) provide equivalent performance at half the current rating.

HAS 50-P and HAS 50-S measure 50A. HAS 50-P is marked Not For New Designs and should not be selected for new circuit designs. HAS 50-S (Active status, MSL Not Applicable) is the recommended 50A option for new applications.

Product Status Considerations

For new design implementations, select only from parts with Active product status: HAS 200-P, HAS 200-S, HAS 100-P, HAS 100-S, and HAS 50-S. HAS 50-P (Not For New Designs) is available for legacy system support and replacement applications only.

Compliance & Regulatory

All substitute parts carry identical RoHS Compliant and REACH Unaffected designations, ensuring regulatory compliance across the HAS series. ECCN and HTSUS classifications are uniform, supporting consistent export and procurement documentation.

Frequently Asked Questions (FAQ)

Q: Can HAS 100-P substitute for HAS 200-P in a 200A measurement application?

A: No. The HAS 100-P is rated for maximum 100A current sensing. Using it in a 200A application exceeds its specified measurement range and produces inaccurate results. Select HAS 200-P or HAS 200-S for 200A applications.

Q: What is the difference between HAS 200-P and HAS 200-S?

A: Both measure 200A with identical electrical performance. The difference is MSL (Moisture Sensitivity Level): HAS 200-P has MSL 1 (Unlimited), while HAS 200-S has MSL Not Applicable. Choose based on your assembly and storage moisture control requirements.

Q: Why is HAS 50-P marked "Not For New Designs"?

A: HAS 50-P is a legacy product. For new circuit designs requiring 50A measurement, use HAS 50-S, which maintains Active status and identical electrical specifications.

Q: Are all HAS series sensors pin-compatible?

A: All HAS series sensors use Through Hole mounting and Module package type with identical electrical interfaces (±15V supply, ratiometric voltage output). Pin compatibility depends on specific PCB layout; consult mechanical drawings for exact footprint confirmation.

Q: Can I use HAS 100-S in place of HAS 100-P?

A: Yes, for 100A applications. Both sensors have identical electrical specifications. The difference is MSL designation. HAS 100-S (MSL Not Applicable) is suitable if your assembly process does not require MSL 1 (Unlimited) moisture sensitivity rating.

Q: What is the frequency response limit for all HAS series sensors?

A: All HAS series sensors operate across DC to 50kHz frequency range with 3µs response time. This specification is uniform across HAS 200-P, HAS 200-S, HAS 100-P, HAS 100-S, HAS 50-P, and HAS 50-S.

Q: Are there current rating options between 50A and 100A?

A: No. The HAS series provides discrete current ratings: 50A, 100A, and 200A. No intermediate ratings are available within this product line.

Q: Do all HAS sensors require ±15V supply voltage?

A: Yes. All HAS series sensors require ±15V supply voltage. This specification is identical across all models and variants.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message