FGG.0B.306.CLAD35Z Equivalent & Substitute Parts

Part Overview

The FGG.0B.306.CLAD35Z is a 6-position circular connector plug with male pins and solder cup termination, manufactured by LEMO. This connector is classified as a shielded, push-pull fastening connector with gold-plated mating contacts and operates across an extended temperature range of -55°C to 250°C. The product is active and in stock with 768 units available. Alternative models are identified to support procurement flexibility, supply chain continuity, and application-specific requirements where equivalent electrical and mechanical parameters are maintained.

Substiute Parts

FGG.0B.306.CLAD35Z

LEMOIn Stock: 815FGG.0B.306.CLAD35Z Datasheet

Current PartRFQ

S20L0C-P06MCC0-420S

ODUIn Stock: 794S20L0C-P06MCC0-420S Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

The substitute part S20L0C-P06MCC0-420S (ODU MINI-SNAP® L series) qualifies as an equivalent based on the following critical parameters:

• Connector Configuration: Both are 6-position male plug connectors with solder cup termination
• Fastening Mechanism: Both employ push-pull fastening
• Contact System: Both feature gold-plated mating contacts on brass base material
• Shielding: Both are shielded connectors with IP50 ingress protection
• Insert Material: Both use PEEK for the insulator
• Regulatory Compliance: Both are ROHS3 compliant and REACH unaffected
• Termination Method: Both support solder cup wire termination

The substitution is valid where the operating temperature range and current rating requirements of the application fall within the overlapping specifications of both connectors.

Parameter Comparison

Engineering Selection Recommendations

Selection between FGG.0B.306.CLAD35Z and S20L0C-P06MCC0-420S is determined by application-specific requirements:

Use FGG.0B.306.CLAD35Z when:

• Operating temperature range extends below -40°C or above 120°C
• Extended temperature capability to 250°C is required
• Current requirements do not exceed 2.5A

Use S20L0C-P06MCC0-420S when:

• Operating temperature range is -40°C to 120°C
• Current requirements up to 4A are needed
• Additional shell finish protection (chrome over nickel) is beneficial
• Strain relief features are required

Both connectors maintain ROHS3 compliance and REACH unaffected status, supporting equivalent regulatory requirements for industrial, medical, military, and testing equipment applications.

Frequently Asked Questions (FAQ)

Q: Can S20L0C-P06MCC0-420S directly replace FGG.0B.306.CLAD35Z in all applications?

A: Direct replacement is valid only when the application operating temperature remains within -40°C to 120°C and current does not exceed 2.5A. Applications requiring temperatures below -40°C or above 120°C must use the LEMO connector.

Q: What is the primary difference between these two connectors?

A: The primary differences are operating temperature range (LEMO: -55°C to 250°C; ODU: -40°C to 120°C) and current rating (LEMO: 2.5A; ODU: 4A). All other electrical and mechanical parameters are equivalent.

Q: Are the solder cup terminations compatible between these connectors?

A: Both connectors use solder cup termination with identical contact material (brass) and finish (gold). Solder cup dimensions and wire gauge acceptance ranges differ slightly; verify cable opening specifications for your specific wire gauge.

Q: Do both connectors support the same mating interface?

A: Both are 6-position male plug connectors with push-pull fastening and shielded design. Physical mating compatibility depends on the corresponding female receptacle design and shell size specifications.

Q: Are there any compliance or certification differences?

A: Both connectors are ROHS3 compliant and REACH unaffected. No material flammability rating is specified for the ODU connector in the provided data. Verify UL94 V-0 compliance requirements for your application.