FCE17A15SC4DB D-Sub 15 Position Receptacle Equivalent & Substitute Parts

Part Overview

The FCE17A15SC4DB is a 15 position D-Sub receptacle connector manufactured by Amphenol ICC (Commercial Products). This connector features female sockets in a right-angle, through-hole solder configuration with a 2-row layout (Shell Size 2, DA/A). The part is actively produced and maintains an inventory of 676 pieces in new original condition.

D-Sub receptacle connectors serve as mating interfaces for signal transmission in electronic assemblies. Equivalent and substitute parts become necessary when the primary part experiences supply constraints, when alternative sourcing is required for cost optimization, or when design flexibility across manufacturing partners is needed while maintaining electrical and mechanical compatibility.

Substiute Parts

FCE17A15SC4DB

Amphenol ICC (Commercial Products)In Stock: 749FCE17A15SC4DB Datasheet

Current PartRFQ

183-015-213R541

NorComp Inc.In Stock: 1203183-015-213R541 Datasheet

SimilarRFQ

5745113-2

TE Connectivity AMP ConnectorsIn Stock: 14175745113-2 Datasheet

SimilarRFQ

5745984-4

TE Connectivity AMP ConnectorsIn Stock: 11175745984-4 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the FCE17A15SC4DB is determined by strict alignment of the following critical parameters:

Mandatory Matching Parameters:

• Connector Style: D-Sub
• Connector Type: Receptacle, Female Sockets
• Number of Positions: 15
• Number of Rows: 2
• Shell Size, Connector Layout: 2 (DA, A)
• Mounting Type: Through Hole, Right Angle
• Termination: Solder

Compatible Variation Parameters:

• Current Rating: Minimum 5A (higher ratings acceptable)
• Operating Temperature: Must encompass or exceed -40°C ~ 85°C range
• Shell Material Finish: Steel with tin or nickel plating acceptable
• Contact Finish: Gold plating required
• Material Flammability Rating: UL94 V-0 required
• RoHS Compliance: RoHS Compliant or ROHS3 Compliant acceptable
• Backset Spacing: 0.590" (14.99mm) preferred; minor variations within connector tolerance acceptable

The three substitute parts listed below satisfy all mandatory matching parameters and maintain electrical and mechanical compatibility with the FCE17A15SC4DB.

Parameter Comparison

Engineering Selection Recommendations

FCE17A15SC4DB (Amphenol ICC) - Primary Part

The FCE17A15SC4DB remains the primary selection when Amphenol ICC sourcing is preferred or contractually specified. This part carries active product status, RoHS compliance, and maintains adequate inventory (676 pieces). The operating temperature range of -40°C ~ 85°C is suitable for standard commercial and industrial applications.

183-015-213R541 (NorComp Inc.) - Substitute

The NorComp 183-015-213R541 is a direct functional substitute with identical position count, shell size, and solder termination. This part offers an extended operating temperature range (-55°C ~ 105°C), making it suitable for applications requiring broader thermal performance. The nickel-plated steel shell provides alternative corrosion resistance compared to tin plating. NorComp maintains higher inventory availability (1110 pieces) and carries ROHS3 compliance with REACH unaffected status. The panel mount capability provides additional mounting flexibility. Note: Contact material is brass rather than phosphor bronze, and contact finish thickness is flash specification.

5745113-2 (TE Connectivity AMPLIMITE HDP-20) - Substitute

The TE Connectivity 5745113-2 provides equivalent functionality with a higher current rating (6A versus 5A) and extended operating temperature range (-55°C ~ 105°C). This part features phosphor bronze contacts matching the primary part material and carries ROHS3 compliance with REACH unaffected status. Inventory availability is strong (1354 pieces). The backset spacing of 0.545" (13.84mm) represents a minor deviation from the primary part specification of 0.590" (14.99mm); this variation falls within standard D-Sub connector tolerance ranges and does not affect mating compatibility. A 125V voltage rating is specified for this part.

5745984-4 (TE Connectivity AMPLIMITE HD-20) - Substitute

The TE Connectivity 5745984-4 offers equivalent functionality with matching backset spacing (0.590" / 14.99mm), higher current rating (6A), and extended operating temperature range (-55°C ~ 105°C). This part features phosphor bronze contacts and carries RoHS compliance with REACH unaffected status. Inventory availability is adequate (1105 pieces). The ground strap feature and 30.0µin (0.76µm) contact finish thickness provide enhanced electrical performance characteristics. A 125V voltage rating is specified.

All substitute parts maintain active product status and meet the mandatory electrical and mechanical compatibility requirements for direct substitution with the FCE17A15SC4DB.

Frequently Asked Questions (FAQ)

Q: Can the 183-015-213R541 (NorComp) be used as a direct replacement for the FCE17A15SC4DB?

A: Yes. The 183-015-213R541 matches all mandatory parameters: 15 positions, 2 rows, Shell Size 2 (DA/A), right-angle through-hole solder termination, and 5A current rating. The extended operating temperature range (-55°C ~ 105°C) encompasses the primary part's range (-40°C ~ 85°C). The nickel-plated steel shell and brass contacts provide equivalent electrical performance. The panel mount capability is an additional feature that does not prevent substitution.

Q: What is the significance of the backset spacing difference in the 5745113-2?

A: The 5745113-2 specifies 0.545" (13.84mm) backset spacing compared to 0.590" (14.99mm) in the primary part and other substitutes. This 0.045" (1.15mm) difference falls within standard D-Sub connector manufacturing tolerances and does not affect mating compatibility with standard D-Sub plugs. The connector will function identically in circuit applications.

Q: Are there differences in contact material between these parts?

A: Yes. The primary part (FCE17A15SC4DB) and two TE Connectivity substitutes (5745113-2 and 5745984-4) use phosphor bronze contacts. The NorComp 183-015-213R541 uses brass contacts. Both materials provide adequate electrical conductivity and contact reliability for signal transmission applications. The choice between them depends on application-specific requirements for spring force, wear resistance, and corrosion performance.

Q: What does the contact finish thickness specification indicate?

A: Contact finish thickness indicates the gold plating depth on the contact surfaces. The primary part specifies 15.0µin (0.38µm), while the 5745984-4 specifies 30.0µin (0.76µm), and the 183-015-213R541 specifies flash thickness. Thicker gold plating generally provides enhanced corrosion resistance and contact durability in high-cycle mating applications. Flash thickness provides minimal gold coverage for corrosion protection. All specifications ensure adequate electrical performance for standard signal transmission.

Q: How do the current ratings affect substitution decisions?

A: The primary part is rated for 5A, while both TE Connectivity substitutes are rated for 6A. A higher current rating indicates the substitute can safely handle equal or greater current loads. Substituting a 6A-rated connector for a 5A-rated application presents no electrical risk. Current rating selection should be based on actual circuit requirements, not connector rating alone.

Q: What is the difference between RoHS Compliant and ROHS3 Compliant?

A: Both designations indicate compliance with Restriction of Hazardous Substances regulations. RoHS Compliant refers to the original RoHS Directive (2002/95/EC), while ROHS3 Compliant refers to the recast directive (2011/65/EU). ROHS3 includes additional restricted substances and represents current regulatory compliance. Both are acceptable for substitution purposes in applications requiring RoHS compliance.

Q: Does the ground strap feature in the 5745984-4 affect compatibility?

A: No. The ground strap is an additional feature that provides enhanced grounding capability but does not affect the connector's basic mating and signal transmission function. The presence of a ground strap in the substitute part does not prevent its use in applications designed for the primary part without a ground strap.

Q: Can these connectors be used interchangeably in existing PCB designs?

A: Yes, with one consideration: the 5745113-2 has a 0.045" (1.15mm) difference in backset spacing. If the PCB design includes mounting holes or alignment features specific to the 0.590" spacing, the 5745113-2 may require PCB modification. The other substitutes (183-015-213R541 and 5745984-4) have identical backset spacing and require no PCB changes.

Q: What packaging formats are available for these parts?

A: The primary part (FCE17A15SC4DB) is supplied in standard packaging. The 183-015-213R541 is supplied in trays. Both TE Connectivity substitutes (5745113-2 and 5745984-4) are supplied in bulk packaging. Packaging format does not affect electrical or mechanical compatibility but may influence handling, storage, and inventory management procedures.