ET0901500000G Terminal Block Plug 9-Position 7.62mm Equivalent & Substitute Parts

Part Overview

The ET0901500000G is a 9-position terminal block plug manufactured by Amphenol Anytek, designed for free-hanging in-line applications with 0.300" (7.62mm) pitch spacing. This component features female sockets with screw-rising cage clamp termination and is rated for 32 A at 300 V (UL). The part is currently active in production with 746 units in stock.

Substitute parts are identified when equivalent mechanical and electrical parameters allow direct replacement in the same application context. Substitution becomes necessary due to supply chain availability, lead time requirements, or inventory management across multiple approved suppliers.

Substiute Parts

ET0901500000G

Amphenol AnytekIn Stock: 832ET0901500000G Datasheet

Current PartRFQ

1804975

Phoenix ContactIn Stock: 9731804975 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility is determined by matching critical mechanical and electrical parameters. The ET0901500000G and its identified substitute (Phoenix Contact 1804975) share the following core equivalencies:

Matched Critical Parameters:

• 9-position configuration
• 0.300" (7.62mm) pitch spacing
• 180° free-hanging in-line wire entry
• Screw-rising cage clamp termination
• Female socket plug type
• Retention latches on non-wire side
• Tin contact mating finish
• Green housing color
• UL94 V-0 flammability rating
• MSL 1 rating

Parameter Variations Affecting Substitution Scope:

• Wire gauge range: ET0901500000G supports 8-24 AWG (2.5-10mm²); substitute supports 10-30 AWG (0.2-4mm²)
• Current rating: ET0901500000G rated 32 A (UL); substitute rated 5 A (UL)
• Voltage rating: ET0901500000G rated 300 V (UL); substitute rated 600 V (UL)
• Screw size: ET0901500000G uses M3.5; substitute uses M3
• Torque specification: ET0901500000G requires 0.79 Nm; substitute requires 0.5-0.6 Nm
• Insulation height: ET0901500000G measures 0.902" (22.90mm); substitute measures 0.713" (18.10mm)

Substitution is valid only when the application electrical requirements (current and voltage) do not exceed the substitute part's ratings and wire gauge compatibility exists within the overlapping range (10-24 AWG / 2.5-4mm²).

Parameter Comparison

Engineering Selection Recommendations

Primary Part Selection (ET0901500000G): Use the ET0901500000G when applications require the full 32 A current capacity at 300 V (UL rating). This part accommodates wire gauges from 8-24 AWG (2.5-10mm²) and operates across the -40°C to 115°C temperature range. The M3.5 screw specification and 0.79 Nm torque requirement must be observed during installation. ROHS3 compliance and UL94 V-0 flammability rating satisfy stringent regulatory requirements.

Substitute Part Selection (1804975 - Phoenix Contact): The Phoenix Contact 1804975 is electrically and mechanically compatible only for applications where current requirements do not exceed 5 A at UL rating. This substitute is suitable for lower-power signal distribution or control circuits. The reduced wire gauge overlap (10-24 AWG / 2.5-4mm²) restricts use to smaller conductor sizes. The M3 screw and lower torque specification (0.5-0.6 Nm) require adjusted installation procedures. The lower insulation height (18.10mm vs. 22.90mm) may affect panel cutout compatibility.

Substitution Constraints:

• Do not substitute the Phoenix Contact 1804975 in applications exceeding 5 A at UL rating
• Do not use the substitute when wire gauges smaller than 10 AWG (0.2-2.4mm²) are required
• Verify screw size compatibility (M3.5 vs. M3) with existing installation tooling
• Confirm panel mounting dimensions accommodate the 18.10mm insulation height of the substitute
• Both parts maintain identical pitch (7.62mm), wire entry angle (180°), and termination method (screw-rising cage clamp)

Compliance Status: Both parts are active products with current manufacturing status. Both achieve RoHS compliance and MSL 1 rating. The ET0901500000G carries ROHS3 designation; the substitute carries standard RoHS designation. Both are classified under HTSUS 8536.90.4000 and ECCN EAR99.

Frequently Asked Questions (FAQ)

Q: Can the Phoenix Contact 1804975 directly replace the ET0901500000G in all applications?

A: No. The Phoenix Contact substitute is rated for 5 A maximum at UL, while the ET0901500000G is rated for 32 A. Substitution is valid only for applications where actual current draw does not exceed 5 A. Voltage rating (600 V UL for substitute vs. 300 V for main part) is not a limiting factor for substitution in lower-voltage applications.

Q: What wire gauge compatibility exists between these two parts?

A: The ET0901500000G accepts 8-24 AWG (2.5-10mm²). The Phoenix Contact 1804975 accepts 10-30 AWG (0.2-4mm²). The overlapping compatible range is 10-24 AWG (2.5-4mm²). Applications requiring 8-9 AWG (10mm²) conductors cannot use the substitute.

Q: Are the screw specifications interchangeable?

A: No. The ET0901500000G uses M3.5 screws with 0.79 Nm torque specification. The Phoenix Contact 1804975 uses M3 screws with 0.5-0.6 Nm torque specification. Installation tooling and torque procedures must be adjusted accordingly when switching between parts.

Q: Will the Phoenix Contact substitute fit in the same panel cutout as the ET0901500000G?

A: The insulation heights differ: ET0901500000G measures 0.902" (22.90mm) while the substitute measures 0.713" (18.10mm). The substitute is shorter and will fit in the same cutout, but the reduced height may affect sealing or aesthetic alignment depending on panel design.

Q: Are both parts RoHS compliant?

A: Yes. The ET0901500000G is ROHS3 compliant. The Phoenix Contact 1804975 is RoHS compliant. Both meet environmental regulatory requirements. The ROHS3 designation on the main part indicates compliance with the most recent RoHS directive revision.

Q: What is the significance of the MSL 1 rating for both parts?

A: MSL 1 (Moisture Sensitivity Level 1) indicates unlimited shelf life with no special moisture control requirements during storage or handling. Both parts can be stored under standard warehouse conditions without desiccant packaging or humidity monitoring.

Q: Can these parts be used interchangeably in 24 V DC control circuits?

A: Yes, for 24 V DC applications where current does not exceed 5 A. Both parts are rated for 300 V (main) and 600 V (substitute) at UL, which exceeds 24 V requirements. The 5 A limit of the substitute becomes the controlling factor. Wire gauge must fall within the 10-24 AWG overlap range.

Q: What is the difference between the series designations (04-762 vs. COMBICON PC)?

A: Series designations identify product families within each manufacturer's catalog. The 04-762 series is Amphenol Anytek's designation; COMBICON PC is Phoenix Contact's designation. These are manufacturer-specific identifiers and do not affect electrical or mechanical compatibility.

Q: Are operating temperature ranges specified for both parts?

A: The ET0901500000G specifies -40°C to 115°C operating range. The Phoenix Contact 1804975 does not provide an operating temperature specification in the available data. Applications requiring operation outside standard industrial temperature ranges should use the ET0901500000G with its documented temperature rating.

Q: What inventory considerations apply to these parts?

A: The ET0901500000G has 746 units in stock. The Phoenix Contact 1804975 has 874 units in stock. The substitute has higher current availability. For time-sensitive procurement, the substitute may offer faster delivery, provided electrical and mechanical requirements are satisfied.