ET05SD1AGE Toggle Switch SPDT Equivalent & Substitute Parts

Part Overview

The ET05SD1AGE is an active production toggle switch manufactured by C&K, featuring SPDT (Single Pole Double Throw) circuitry with momentary-off-momentary switching function. This through-hole, right-angle mounted component is rated for 2A at 120V AC and 28V DC, with IP57 ingress protection and epoxy sealed terminals. The part is supplied in tray packaging with 1165 units currently in stock.

Equivalent and substitute parts are identified when design requirements permit operation within reduced electrical ratings or when packaging format changes are acceptable for the application.

Substiute Parts

ET05SD1AGE

C&KIn Stock: 1203ET05SD1AGE Datasheet

Current PartRFQ

ET05SD1ABE

C&KIn Stock: 1198ET05SD1ABE Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of ET05SD1AGE with ET05SD1ABE is permissible when the application electrical requirements fall within the reduced ratings of the substitute part. Both components share identical mechanical and environmental specifications:

Common Parameters (Substitution Basis):

• Series: ET
• Circuit Configuration: SPDT
• Switch Function: Mom-Off-Mom
• Mounting Type: Through Hole, Right Angle
• Actuator Type: Standard Round
• Actuator Length: 10.16mm
• Termination Style: PC Pin
• Ingress Protection: IP57
• Operating Temperature Range: -30°C to 85°C
• Electrical Life: 30,000 Cycles
• RoHS Status: ROHS3 Compliant
• Packaging Format: Tray or Bulk (interchangeable for component selection)

Differing Parameters (Limiting Factors):

• Current Rating: 2A (main part) vs. 0.4VA (substitute)
• Voltage Rating - AC: 120V (main part) vs. 20V (substitute)
• Voltage Rating - DC: 28V (main part) vs. 20V (substitute)

Substitution is valid only when circuit design operates at or below 0.4VA current and 20V maximum voltage (both AC and DC).

Parameter Comparison

Engineering Selection Recommendations

Both ET05SD1AGE and ET05SD1ABE are active production components with ROHS3 compliance and REACH compliance status. Selection between these parts is determined solely by electrical operating requirements:

• ET05SD1AGE is specified for applications requiring 2A current capacity and voltage ratings up to 120V AC or 28V DC.
• ET05SD1ABE is specified for applications operating at 0.4VA maximum current and 20V maximum voltage (AC and DC).

Both components maintain identical mechanical form factor, environmental protection rating (IP57), and thermal operating range. Packaging format (tray vs. bulk) does not affect component functionality or compatibility.

Frequently Asked Questions (FAQ)

Q: Can ET05SD1ABE replace ET05SD1AGE in all applications?

A: No. ET05SD1ABE substitution is valid only when the circuit operates at or below 0.4VA current and 20V maximum voltage. Applications requiring 2A current or voltages exceeding 20V must use ET05SD1AGE.

Q: Are the mechanical dimensions identical between these parts?

A: Yes. Both parts share identical mounting type (through hole, right angle), actuator type (standard round), and actuator length (10.16mm). Panel cutout dimensions and bushing specifications are equivalent.

Q: Does packaging format affect component selection?

A: No. ET05SD1AGE is supplied in tray packaging and ET05SD1ABE in bulk packaging. Packaging format does not affect electrical performance, mechanical compatibility, or environmental ratings. Selection is based on electrical requirements and inventory availability.

Q: Are both parts suitable for the same temperature range?

A: Yes. Both ET05SD1AGE and ET05SD1ABE operate across -30°C to 85°C and maintain 30,000 cycle electrical life rating across this range.

Q: What compliance certifications apply to both parts?

A: Both parts are ROHS3 compliant and REACH affected. Compliance status is identical between the main part and substitute.