ESR25JZPJ113 Equivalent & Substitute Parts

Part Overview

The ESR25JZPJ113 is a 11 kOhms ±5% thick film chip resistor manufactured by Rohm Semiconductor in the 1210 (3225 Metric) package with 0.667W power rating. This component is rated for automotive applications under AEC-Q200 and features pulse withstanding capability. The part is currently in active production status.

Substitute parts are necessary when the primary part experiences supply constraints, inventory limitations, or when design requirements permit alternative manufacturers while maintaining electrical and mechanical compatibility.

Substiute Parts

ESR25JZPJ113

Rohm SemiconductorIn Stock: 904ESR25JZPJ113 Datasheet

Current PartRFQ

ERJ-P14J113U

Panasonic Electronic ComponentsIn Stock: 13950ERJ-P14J113U Datasheet

DirectRFQ

ERJ-14YJ113U

Panasonic Electronic ComponentsIn Stock: 3633ERJ-14YJ113U Datasheet

UpgradeRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the ESR25JZPJ113 is determined by the following criteria:

Mandatory Matching Parameters:

• Resistance value: 11 kOhms
• Tolerance: ±5%
• Package / Case: 1210 (3225 Metric)
• Composition: Thick Film
• Temperature Coefficient: ±200ppm/°C
• Operating Temperature Range: -55°C ~ 155°C
• Automotive Rating: AEC-Q200
• RoHS Status: ROHS3 Compliant
• Moisture Sensitivity Level: 1 (Unlimited)

Allowable Variation:

• Power Rating: Substitute parts may have equal or lower power ratings (0.5W minimum acceptable for this application context)

The identified substitute parts meet all mandatory parameters. Variations in power rating and product status are noted in the comparison table below.

Parameter Comparison

Engineering Selection Recommendations

ERJ-P14J113U (Panasonic Electronic Components) is the primary substitute for the ESR25JZPJ113. This part maintains active product status and meets all mandatory electrical and mechanical parameters. The 0.5W power rating is lower than the original 0.667W specification; applications must confirm that 0.5W capacity is sufficient for the circuit design. The seated height difference of 0.002" (0.05mm) is within typical PCB assembly tolerances.

ERJ-14YJ113U (Panasonic Electronic Components) is classified as "Not For New Designs" and should be used only in legacy system maintenance or replacement scenarios where the original ESR25JZPJ113 is unavailable and ERJ-P14J113U cannot be sourced. This part carries the same electrical specifications and physical constraints as ERJ-P14J113U.

Frequently Asked Questions (FAQ)

Q: Can ERJ-P14J113U be used as a direct replacement for ESR25JZPJ113?

A: Yes, ERJ-P14J113U is electrically and mechanically compatible. The primary consideration is power rating: ERJ-P14J113U is rated at 0.5W versus ESR25JZPJ113 at 0.667W. Circuit design must confirm that 0.5W dissipation capacity meets application requirements.

Q: What is the difference between ERJ-P14J113U and ERJ-14YJ113U?

A: Both parts are identical in electrical specifications and physical dimensions. The key difference is product status: ERJ-P14J113U is active for new designs, while ERJ-14YJ113U is not recommended for new designs. For new applications, ERJ-P14J113U is the preferred choice.

Q: Are there physical compatibility concerns with the substitute parts?

A: The seated height of substitute parts is 0.028" (0.70mm) compared to 0.026" (0.65mm) for the original part. This 0.002" difference is within standard PCB assembly tolerances and does not affect mechanical fit or electrical performance in standard 1210 package footprints.

Q: Do the substitute parts maintain automotive compliance?

A: Yes, both ERJ-P14J113U and ERJ-14YJ113U are AEC-Q200 rated and ROHS3 compliant, matching the original ESR25JZPJ113 specifications.

Q: What is the impact of lower power rating on circuit performance?

A: The 0.5W rating of substitute parts is lower than the original 0.667W. Applications must calculate actual power dissipation in the resistor to ensure it does not exceed 0.5W under maximum operating conditions. If dissipation exceeds 0.5W, the substitute parts are not suitable.