ESR18EZPJ823 Equivalent & Substitute Parts

Part Overview

The ESR18EZPJ823 is a 1206 (3216 Metric) thick film chip resistor manufactured by Rohm Semiconductor, rated at 82 kOhms ±5% with 0.5W power dissipation capability. This component is designed for automotive applications and carries AEC-Q200 qualification with pulse withstanding capability. The part is currently in active production status with 1117 units available in inventory. Substitute parts are identified when equivalent electrical specifications and mechanical compatibility are maintained within the allowed parameter tolerances for this resistor category.

Substiute Parts

ESR18EZPJ823

Rohm SemiconductorIn Stock: 1166ESR18EZPJ823 Datasheet

Current PartRFQ

ERJ-P08J823V

Panasonic Electronic ComponentsIn Stock: 14711ERJ-P08J823V Datasheet

DirectRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the ESR18EZPJ823 is determined by the following criteria:

Electrical Parameters (Must Match):

• Resistance value: 82 kOhms
• Tolerance: ±5%
• Temperature coefficient: ±200ppm/°C
• Operating temperature range: -55°C ~ 155°C

Mechanical Parameters (Must Match):

• Package / Case: 1206 (3216 Metric)
• Number of terminations: 2
• Physical dimensions: 0.126" L x 0.063" W (3.20mm x 1.60mm)

Compliance & Ratings (Must Match):

• Automotive qualification: AEC-Q200
• RoHS Status: ROHS3 Compliant
• Composition: Thick Film
• Features: Pulse Withstanding

Power Rating Consideration: Substitute parts may have equal or higher power dissipation ratings. The ESR18EZPJ823 is rated at 0.5W; substitutes with 0.667W or higher ratings are acceptable as they provide equivalent or superior thermal performance within the same package envelope.

Parameter Comparison

Engineering Selection Recommendations

The ERJ-P08J823V from Panasonic Electronic Components is a direct substitute for the ESR18EZPJ823. Both components meet identical electrical specifications, share the same 1206 package footprint, and carry AEC-Q200 automotive qualification. The Panasonic substitute provides a higher power rating (0.667W versus 0.5W) within the same physical envelope, offering improved thermal margin without any dimensional or compliance trade-offs. Both parts are ROHS3 compliant and maintain identical temperature coefficients and operating ranges. Selection between these parts may be based on availability, supply chain requirements, or design margin preferences.

Frequently Asked Questions (FAQ)

Q: Can the ERJ-P08J823V replace the ESR18EZPJ823 in automotive applications?

A: Yes. Both components carry AEC-Q200 qualification, maintain identical resistance values and tolerances, and operate across the same temperature range (-55°C ~ 155°C). The Panasonic substitute is fully compatible for automotive use.

Q: What is the difference in power rating between these parts?

A: The ESR18EZPJ823 is rated at 0.5W, while the ERJ-P08J823V is rated at 0.667W. Both are housed in the same 1206 package. The higher power rating of the substitute provides additional thermal headroom without affecting circuit performance or board layout.

Q: Are the physical dimensions identical?

A: The length and width are identical (0.126" L x 0.063" W / 3.20mm x 1.60mm). The seated height differs slightly: ESR18EZPJ823 at 0.026" (0.65mm) maximum versus ERJ-P08J823V at 0.028" (0.70mm) maximum. This 0.002" difference is negligible for standard PCB assembly and does not affect component placement or clearance in typical designs.

Q: Do both parts have the same moisture sensitivity rating?

A: Yes. Both components are rated MSL 1 (Unlimited), indicating no moisture sensitivity restrictions for storage or handling.

Q: Are there any compliance differences between these substitutes?

A: No. Both parts are ROHS3 compliant, REACH unaffected, and classified under the same ECCN (EAR99) and HTSUS codes (8533.21.0030).

Q: What packaging formats are available for each part?

A: The ESR18EZPJ823 is supplied in Tape & Reel (TR) format. The ERJ-P08J823V is available in Cut Tape (CT) and Digi-Reel® formats. Packaging selection should align with assembly process requirements.