ESR10EZPJ113 Equivalent & Substitute Parts

Part Overview

The ESR10EZPJ113 is an 11 kOhms ±5% thick film chip resistor in 0805 (2012 Metric) package manufactured by Rohm Semiconductor. This component is rated for 0.4W power dissipation and meets automotive AEC-Q200 qualification with pulse withstanding capability. The part is active in production with ROHS3 compliance and unlimited moisture sensitivity rating (MSL 1). Substitute parts are identified when equivalent electrical specifications, mechanical compatibility, and automotive certifications align with the original component requirements.

Substiute Parts

ESR10EZPJ113

Rohm SemiconductorIn Stock: 688ESR10EZPJ113 Datasheet

Current PartRFQ

ERJ-P06J113V

Panasonic Electronic ComponentsIn Stock: 19728ERJ-P06J113V Datasheet

UpgradeRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the ESR10EZPJ113 is determined by the following critical parameters:

• Resistance value: 11 kOhms (exact match required)
• Tolerance: ±5% (exact match required)
• Package: 0805 (2012 Metric) (exact match required)
• Composition: Thick Film (exact match required)
• Temperature Coefficient: ±200ppm/°C (exact match required)
• Operating Temperature Range: -55°C ~ 155°C (exact match or better required)
• Automotive Rating: AEC-Q200 (exact match required)
• Power Rating: Equal or greater than 0.4W (upgrade acceptable)
• RoHS Status: ROHS3 Compliant (exact match required)
• Moisture Sensitivity Level: 1 (exact match required)

The ERJ-P06J113V from Panasonic Electronic Components meets all substitution criteria with a higher power rating (0.5W vs 0.4W), which represents an acceptable upgrade for this component category.

Parameter Comparison

Engineering Selection Recommendations

The ERJ-P06J113V is a direct substitute for the ESR10EZPJ113 based on matching electrical specifications, identical package geometry, and equivalent automotive certifications. Both components are active products with ROHS3 compliance and AEC-Q200 qualification. The ERJ-P06J113V provides a higher power rating (0.5W versus 0.4W), which is an acceptable upgrade that does not compromise circuit performance. The maximum seated height difference of 0.002" (0.05mm) is within typical PCB assembly tolerances and does not affect mechanical fit or thermal performance in standard 0805 footprints.

Frequently Asked Questions (FAQ)

Q: Can ERJ-P06J113V replace ESR10EZPJ113 in automotive applications?

A: Yes. Both components meet AEC-Q200 automotive qualification, operate across the identical temperature range (-55°C ~ 155°C), and share matching electrical parameters (11 kOhms ±5%, ±200ppm/°C). The higher power rating of the substitute part does not create compatibility issues.

Q: Are there mechanical compatibility concerns between these parts?

A: No. Both components use the 0805 (2012 Metric) package with identical length and width (0.079" x 0.049"). The maximum seated height difference is 0.002" (0.05mm), which is negligible for standard PCB assembly and does not affect component placement or thermal management.

Q: Do both parts meet the same compliance standards?

A: Yes. Both ESR10EZPJ113 and ERJ-P06J113V are ROHS3 compliant with MSL 1 (unlimited moisture sensitivity). Both carry AEC-Q200 automotive qualification and pulse withstanding capability.

Q: What is the significance of the power rating difference?

A: The ERJ-P06J113V has a 0.5W rating compared to the ESR10EZPJ113's 0.4W rating. This represents a 25% increase in power dissipation capability. In applications where the original 0.4W part was specified, the higher-rated substitute provides additional thermal margin without affecting electrical performance or circuit behavior.

Q: Are the temperature coefficients identical?

A: Yes. Both components have a temperature coefficient of ±200ppm/°C and operate across -55°C ~ 155°C, ensuring equivalent frequency stability and thermal performance characteristics.