ESLM08200 Equivalent & Substitute Parts

Part Overview

The ESLM08200 is an 8-position wire-to-board terminal block manufactured by Amphenol PCD, designed for horizontal PCB mounting with 0.200" (5.08mm) pitch spacing. This component is classified as Active product status and is RoHS compliant. Alternative equivalent parts may be required due to inventory availability, regional sourcing constraints, or specific application requirements such as current rating compatibility or operating temperature specifications.

Substiute Parts

ESLM08200

Amphenol PCDIn Stock: 901ESLM08200 Datasheet

Current PartRFQ

1729186

Phoenix ContactIn Stock: 25171729186 Datasheet

SimilarRFQ

282837-8

TE Connectivity AMP ConnectorsIn Stock: 924282837-8 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the ESLM08200 terminal block is determined by strict alignment of the following critical parameters:

Core Compatibility Parameters:

• Positions Per Level: 8 (exact match required)
• Pitch: 0.200" (5.08mm) (exact match required)
• Mating Orientation: Horizontal with Board (exact match required)
• Mounting Type: Through Hole (exact match required)
• Wire Termination: Screw - Rising Cage Clamp (exact match required)
• Voltage Rating: 300 V (exact match required)
• Features: Interlocking (Side) (exact match required)

Allowable Variation Parameters:

• Current Rating: Substitute must meet or exceed 14.6 A
• Wire Gauge: Substitute must accommodate 14-30 AWG range or compatible subset
• Operating Temperature: Substitute must support application requirements
• Housing Material: Polyamide variants acceptable
• Contact/Clamp/Screw Plating: Material composition variations permitted if electrical performance maintained
• RoHS/REACH Compliance: Compliance status may differ based on regional requirements

Two substitute parts meet these criteria: Phoenix Contact 1729186 and TE Connectivity 282837-8.

Parameter Comparison

Engineering Selection Recommendations

ESLM08200 (Amphenol PCD): Primary selection for applications requiring RoHS compliance and 14.6 A current capacity. Suitable for standard industrial and commercial applications with -40°C to 110°C operating temperature range.

1729186 (Phoenix Contact): Alternative for applications where current rating of 10 A is sufficient. ROHS3 compliant. Note: Current rating is 4.6 A lower than the main part. Suitable for lower-power applications. Bulk packaging available with higher inventory.

282837-8 (TE Connectivity): Alternative for applications matching 14.6 A current requirement and 16-28 AWG wire gauge compatibility. RoHS non-compliant status requires verification against regional regulatory requirements. Bulk packaging available.

Selection should be based on current rating requirements, regulatory compliance mandates, wire gauge compatibility, and packaging format needs.

Frequently Asked Questions (FAQ)

Q: Can 1729186 replace ESLM08200 in all applications? A: No. The 1729186 has a maximum current rating of 10 A compared to 14.6 A for the ESLM08200. Substitution is valid only for applications where the circuit current does not exceed 10 A.

Q: What is the primary difference between 282837-8 and ESLM08200? A: The 282837-8 accepts wire gauge 16-28 AWG, whereas ESLM08200 accepts 14-30 AWG. The 282837-8 is RoHS non-compliant. Both share identical voltage, current, pitch, and mounting specifications.

Q: Are all three parts mechanically interchangeable? A: Yes, all three parts share identical pitch (5.08mm), mounting orientation (horizontal with board), mounting type (through hole), and wire termination method (screw - rising cage clamp). Mechanical interchangeability is confirmed.

Q: Does RoHS compliance status affect electrical performance? A: No. RoHS compliance indicates material composition restrictions but does not alter electrical performance. Selection based on compliance status depends on application regulatory requirements.

Q: What packaging formats are available? A: ESLM08200 is supplied in Tray packaging. Both 1729186 and 282837-8 are supplied in Bulk packaging. Packaging selection may affect procurement and handling procedures.

Q: Can wire gauge differences affect substitution decisions? A: Yes. If the application requires 14 AWG or 15 AWG wire termination, only ESLM08200 is suitable. The 282837-8 minimum wire gauge is 16 AWG. The 1729186 accommodates the full 14-30 AWG range.