Equivalent & Substitute Parts for ERJ-S08F10R2V

Part Overview

The ERJ-S08F10R2V is a 10.2 Ohm ±1% 0.25W thick film chip resistor in 1206 (3216 Metric) package manufactured by Panasonic Electronic Components. This part is classified as Active product status and features anti-sulfur coating with automotive AEC-Q200 qualification. Substitute parts are necessary when the primary part experiences supply constraints, inventory depletion, or when design requirements permit selection from qualified alternative manufacturers while maintaining electrical and mechanical compatibility.

Key Parameters

Parameter	Value
Resistance	10.2 Ohms
Tolerance	±1%
Power Rating	0.25W (1/4W)
Package / Case	1206 (3216 Metric)
Composition	Thick Film
Temperature Coefficient	±100ppm/°C
Operating Temperature Range	-55°C ~ 155°C
RoHS Status	ROHS3 Compliant
Moisture Sensitivity Level	1 (Unlimited)

Substitute Part Grouping Explanation

Substitution eligibility for the ERJ-S08F10R2V is determined by strict equivalence across the following parameters:

Resistance value: 10.2 Ohms
Tolerance: ±1%
Power rating: 0.25W (1/4W)
Package: 1206 (3216 Metric)
Composition: Thick Film
Temperature coefficient: ±100ppm/°C
Operating temperature range: -55°C ~ 155°C
RoHS compliance: ROHS3 Compliant
Moisture sensitivity level: 1 (Unlimited)

All substitute parts listed meet these core electrical and mechanical parameters. Variations in product status, specific feature sets (such as anti-sulfur coating or automotive qualification), and dimensional tolerances are noted in the comparison table below.

Parameter Comparison

Parameter	ERJ-S08F10R2V (Main)	ERJ-8ENF10R2V	RC1206FR-0710R2L	RMCF1206FT10R2
Manufacturer	Panasonic Electronic Components	Panasonic Electronic Components	YAGEO	Stackpole Electronics Inc
Resistance	10.2 Ohms	10.2 Ohms	10.2 Ohms	10.2 Ohms
Tolerance	±1%	±1%	±1%	±1%
Power Rating	0.25W	0.25W	0.25W	0.25W
Package	1206 (3216 Metric)	1206 (3216 Metric)	1206 (3216 Metric)	1206 (3216 Metric)
Composition	Thick Film	Thick Film	Thick Film	Thick Film
Temperature Coefficient	±100ppm/°C	±100ppm/°C	±100ppm/°C	±100ppm/°C
Operating Temperature	-55°C ~ 155°C	-55°C ~ 155°C	-55°C ~ 155°C	-55°C ~ 155°C
Product Status	Active	Not For New Designs	Active	Active
Features	Anti-Sulfur, Automotive AEC-Q200	Automotive AEC-Q200	Moisture Resistant	Automotive AEC-Q200
RoHS Status	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant
Moisture Sensitivity Level	1 (Unlimited)	1 (Unlimited)	1 (Unlimited)	1 (Unlimited)
Size / Dimension	0.126" L x 0.063" W (3.20mm x 1.60mm)	0.126" L x 0.063" W (3.20mm x 1.60mm)	0.122" L x 0.063" W (3.10mm x 1.60mm)	0.126" L x 0.063" W (3.20mm x 1.60mm)
Height - Seated (Max)	0.028" (0.70mm)	0.028" (0.70mm)	0.026" (0.65mm)	0.028" (0.70mm)

Engineering Selection Recommendations

Selection among ERJ-S08F10R2V and its substitutes should be based on product lifecycle status and compliance requirements:

ERJ-S08F10R2V is recommended for new designs requiring active product status with anti-sulfur coating and automotive AEC-Q200 qualification.

ERJ-8ENF10R2V carries "Not For New Designs" status and should be used only for legacy system maintenance or repair applications where existing inventory must be maintained.

RC1206FR-0710R2L (YAGEO) is suitable for applications where moisture resistance is the primary feature requirement and active product status is necessary. Dimensional variation (length 3.10mm vs. 3.20mm) must be verified against PCB layout constraints.

RMCF1206FT10R2 (Stackpole Electronics Inc) is suitable for automotive applications requiring AEC-Q200 qualification with active product status. Dimensional specifications match the main part.

All substitute parts maintain ROHS3 compliance and MSL 1 rating, ensuring compatibility with standard manufacturing and storage conditions.

Frequently Asked Questions (FAQ)

Q: Can ERJ-8ENF10R2V be used as a direct replacement for ERJ-S08F10R2V?

A: Electrical and mechanical parameters are identical. However, ERJ-8ENF10R2V carries "Not For New Designs" status. Use only for legacy system support or repair applications where design freeze permits.

Q: What is the significance of the anti-sulfur coating on ERJ-S08F10R2V?

A: Anti-sulfur coating is a feature specific to ERJ-S08F10R2V. Substitute parts without this feature (such as RC1206FR-0710R2L) may not provide equivalent protection in high-sulfur environments. Verify environmental requirements before substitution.

Q: Are dimensional differences between RC1206FR-0710R2L and other substitutes critical?

A: RC1206FR-0710L has length 3.10mm versus 3.20mm for other parts, and height 0.65mm versus 0.70mm. These differences are within 1206 package tolerance but must be verified against PCB footprint design and assembly clearance requirements.

Q: Do all substitute parts meet automotive qualification requirements?

A: ERJ-S08F10R2V, ERJ-8ENF10R2V, and RMCF1206FT10R2 carry AEC-Q200 rating. RC1206FR-0710R2L does not list AEC-Q200 qualification. Verify automotive compliance requirements before selecting RC1206FR-0710R2L for automotive applications.

Q: What is the difference between "Active" and "Not For New Designs" product status?

A: "Active" status indicates the part is in full production and recommended for new designs. "Not For New Designs" indicates the part is in mature phase with limited production support. Use active parts for new designs unless legacy compatibility is required.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message