ERJ-S06F24R9V Equivalent & Substitute Parts

Part Overview

The ERJ-S06F24R9V is a 24.9 Ohm ±1% 1/8W thick film chip resistor in 0805 (2012 Metric) package manufactured by Panasonic Electronic Components. This part is rated for automotive applications under AEC-Q200 and features anti-sulfur construction. The part is active and available in Tape & Reel packaging. Equivalent and substitute parts are identified based on matching electrical specifications, package dimensions, and compliance ratings to support component procurement flexibility and supply chain continuity.

Substiute Parts

ERJ-S06F24R9V

Panasonic Electronic ComponentsIn Stock: 900ERJ-S06F24R9V Datasheet

Current PartRFQ

ERJ-6ENF24R9V

Panasonic Electronic ComponentsIn Stock: 92852ERJ-6ENF24R9V Datasheet

SimilarRFQ

CR0805-FX-24R9ELF

Bourns Inc.In Stock: 23862CR0805-FX-24R9ELF Datasheet

SimilarRFQ

CRCW080524R9FKEA

Vishay DaleIn Stock: 1705CRCW080524R9FKEA Datasheet

SimilarRFQ

CRCW080524R9FKEAHP

Vishay DaleIn Stock: 5608CRCW080524R9FKEAHP Datasheet

SimilarRFQ

CRCW080524R9FKTA

Vishay DaleIn Stock: 10609CRCW080524R9FKTA Datasheet

SimilarRFQ

RC0805FR-0724R9L

YAGEOIn Stock: 5260RC0805FR-0724R9L Datasheet

SimilarRFQ

RCS080524R9FKEA

Vishay DaleIn Stock: 14923RCS080524R9FKEA Datasheet

SimilarRFQ

RMCF0805FT24R9

Stackpole Electronics IncIn Stock: 53949RMCF0805FT24R9 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts are grouped based on the following critical parameters that determine functional equivalence:

Primary Matching Criteria:

• Resistance value: 24.9 Ohms
• Tolerance: ±1%
• Package: 0805 (2012 Metric)
• Composition: Thick Film
• Temperature Coefficient: ±100ppm/°C
• Operating Temperature Range: -55°C ~ 155°C
• Moisture Sensitivity Level: 1 (Unlimited)

Secondary Considerations:

• Power rating (1/8W primary; 1/2W variants listed as higher-rated alternatives)
• Automotive AEC-Q200 certification (where applicable)
• RoHS3 compliance status
• Packaging format (Tape & Reel vs. Cut Tape)

Parts are considered equivalent when all primary criteria match. Parts with higher power ratings (1/2W) are suitable for applications where the original 1/8W rating is sufficient but additional thermal margin is desired. Packaging format differences do not affect electrical performance.

Parameter Comparison

Engineering Selection Recommendations

Direct Equivalents (Identical Specifications): ERJ-6ENF24R9V, CRCW080524R9FKEA, RC0805FR-0724R9L, and RMCF0805FT24R9 are direct functional equivalents to the ERJ-S06F24R9V. All match the 24.9 Ohm resistance, ±1% tolerance, 0.125W power rating, 0805 package, and operating temperature range. All are ROHS3 compliant and carry MSL 1 rating. Selection among these parts depends on packaging preference (Tape & Reel format) and manufacturer availability.

Automotive-Rated Equivalents: For applications requiring AEC-Q200 certification, ERJ-6ENF24R9V, CRCW080524R9FKEA, CRCW080524R9FKEAHP, RCS080524R9FKEA, and RMCF0805FT24R9 maintain automotive qualification. CR0805-FX-24R9ELF and RC0805FR-0724R9L do not carry AEC-Q200 rating and are suitable only for non-automotive applications.

Higher Power Rating Variants: CRCW080524R9FKEAHP and RCS080524R9FKEA provide 0.5W (1/2W) power rating in the same 0805 package. These are suitable for applications where thermal margin above the 0.125W requirement is beneficial. Both maintain AEC-Q200 certification and ROHS3 compliance.

Compliance Considerations: CRCW080524R9FKTA is RoHS non-compliant and REACH affected. This part is not recommended for new designs or applications with RoHS3 requirements.

Frequently Asked Questions (FAQ)

Q: Can I use ERJ-6ENF24R9V as a direct replacement for ERJ-S06F24R9V? A: Yes. Both parts are manufactured by Panasonic, share identical electrical specifications (24.9 Ω, ±1%, 0.125W, 0805 package), and carry AEC-Q200 certification. The primary difference is packaging format: ERJ-S06F24R9V uses Tape & Reel while ERJ-6ENF24R9V uses Cut Tape & Digi-Reel. Electrical performance and reliability are equivalent.

Q: Are the higher power rating parts (0.5W) compatible with my design? A: Yes, if your circuit design specifies 0.125W or lower power dissipation. The 0.5W variants (CRCW080524R9FKEAHP and RCS080524R9FKEA) fit the same 0805 package and maintain all other electrical parameters. Higher power rating provides additional thermal margin without affecting circuit operation. Verify PCB layout accommodates the component height if critical.

Q: Which substitute parts maintain automotive AEC-Q200 certification? A: ERJ-6ENF24R9V, CRCW080524R9FKEA, CRCW080524R9FKEAHP, RCS080524R9FKEA, and RMCF0805FT24R9 all carry AEC-Q200 rating. CR0805-FX-24R9ELF and RC0805FR-0724R9L do not. For automotive applications, select only from the AEC-Q200 qualified list.

Q: What is the difference between Tape & Reel and Cut Tape packaging? A: Both formats contain identical components. Tape & Reel packaging uses continuous tape on a reel suitable for high-volume automated assembly. Cut Tape & Digi-Reel uses pre-cut tape segments in smaller quantities. Electrical specifications and reliability are identical; packaging choice depends on assembly equipment and order volume requirements.

Q: Is CRCW080524R9FKTA suitable for new designs? A: No. This part is RoHS non-compliant and REACH affected. It is not recommended for new product designs or applications with RoHS3 requirements. Use CRCW080524R9FKEA or CRCW080524R9FKEAHP instead.

Q: Do all substitute parts have the same moisture sensitivity level? A: Yes. All listed parts carry MSL 1 (Unlimited), indicating no moisture sensitivity restrictions during storage or handling.

Q: Can I mix different manufacturers in the same design? A: Yes. All listed parts meet identical electrical specifications, package dimensions, and compliance requirements. Mixing manufacturers is acceptable from an electrical standpoint. Verify with your procurement and quality processes for any internal component qualification requirements.