ERJ-S03F6982V Equivalent & Substitute Parts

Part Overview

The ERJ-S03F6982V is a 69.8 kOhms ±1% thick film chip resistor manufactured by Panasonic Electronic Components in 0603 (1608 Metric) package format with 0.1W power rating. This component is rated for automotive applications under AEC-Q200 standard with anti-sulfur properties and operates across -55°C to 155°C temperature range. The part is currently in active production status with ROHS3 compliance and unlimited moisture sensitivity level (MSL 1).

Substitute parts are necessary when the primary part experiences supply constraints, extended lead times, or when design flexibility permits component sourcing from alternative manufacturers while maintaining electrical and mechanical compatibility.

Substiute Parts

ERJ-S03F6982V

Panasonic Electronic ComponentsIn Stock: 1065ERJ-S03F6982V Datasheet

Current PartRFQ

ERJ-3EKF6982V

Panasonic Electronic ComponentsIn Stock: 127130ERJ-3EKF6982V Datasheet

SimilarRFQ

AC0603FR-0769K8L

YAGEOIn Stock: 25400AC0603FR-0769K8L Datasheet

SimilarRFQ

CR0603-FX-6982ELF

Bourns Inc.In Stock: 30319CR0603-FX-6982ELF Datasheet

SimilarRFQ

CRCW060369K8FKEA

Vishay DaleIn Stock: 14781CRCW060369K8FKEA Datasheet

SimilarRFQ

CRCW060369K8FKTA

Vishay DaleIn Stock: 6110CRCW060369K8FKTA Datasheet

SimilarRFQ

RC0603FR-0769K8L

YAGEOIn Stock: 674374RC0603FR-0769K8L Datasheet

SimilarRFQ

RMCF0603FT69K8

Stackpole Electronics IncIn Stock: 195995RMCF0603FT69K8 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the ERJ-S03F6982V is determined by strict equivalence across the following parameters:

• Resistance value: 69.8 kOhms (exact match required)
• Tolerance: ±1% (exact match required)
• Power rating: 0.1W / 1/10W (exact match required)
• Package: 0603 (1608 Metric) (exact match required)
• Composition: Thick Film (exact match required)
• Temperature coefficient: ±100ppm/°C (exact match required)
• Operating temperature range: -55°C ~ 155°C (exact match required)
• Termination count: 2 (exact match required)

All substitute parts listed below meet these core electrical and mechanical parameters. Variations in packaging format (Tape & Reel vs. Cut Tape), physical dimensions within tolerance, and optional features (anti-sulfur, moisture resistant) do not disqualify substitution but may affect procurement and assembly considerations.

Parameter Comparison

Engineering Selection Recommendations

All listed substitute parts maintain full electrical and mechanical equivalence to the ERJ-S03F6982V across core parameters. Selection criteria should prioritize the following factors:

Compliance Status: Parts with ROHS3 compliance (ERJ-3EKF6982V, AC0603FR-0769K8L, CR0603-FX-6982ELF, CRCW060369K8FKEA, RC0603FR-0769K8L, RMCF0603FT69K8) are preferred for applications subject to regulatory requirements. CRCW060369K8FKTA carries RoHS non-compliance and REACH Affected status and should be avoided in regulated applications.

Automotive Certification: Parts rated for AEC-Q200 (ERJ-3EKF6982V, AC0603FR-0769K8L, CRCW060369K8FKEA, CRCW060369K8FKTA, RMCF0603FT69K8) are suitable for automotive circuit applications. Parts without explicit AEC-Q200 rating (CR0603-FX-6982ELF, RC0603FR-0769K8L) may be used in non-automotive applications.

Packaging Format: Tape & Reel format (ERJ-3EKF6982V, AC0603FR-0769K8L, CRCW060369K8FKTA, RMCF0603FT69K8) is standard for high-volume automated assembly. Cut Tape & Digi-Reel format (CR0603-FX-6982ELF, CRCW060369K8FKEA, RC0603FR-0769K8L) accommodates lower-volume or mixed-component procurement.

Inventory Availability: RC0603FR-0769K8L (674,334 pcs) and RMCF0603FT69K8 (195,885 pcs) offer highest stock levels for immediate procurement. ERJ-3EKF6982V (127,040 pcs) provides secondary availability from the original manufacturer.

Frequently Asked Questions (FAQ)

Q: Can I substitute ERJ-S03F6982V with any of these parts without circuit redesign?

A: Yes. All listed parts are electrically and mechanically equivalent across resistance, tolerance, power rating, package, temperature coefficient, and operating temperature range. Direct substitution is permissible without circuit modification.

Q: What is the difference between Tape & Reel and Cut Tape packaging?

A: Tape & Reel packaging is supplied on continuous carrier tape suitable for automated pick-and-place assembly equipment. Cut Tape & Digi-Reel packaging is pre-cut into smaller quantities and is typically used for lower-volume orders or manual assembly. Both formats contain identical components.

Q: Are there physical dimension differences between substitute parts?

A: Minor variations exist within tolerance. The main part and most substitutes measure 0.063" L x 0.031" W (1.60mm x 0.80mm). CRCW series parts measure 0.061" L x 0.033" W (1.55mm x 0.85mm) and 0.063" L x 0.033" W (1.60mm x 0.85mm) respectively. Height differences range from 0.020" to 0.022" (0.50mm to 0.55mm). These variations remain within 0603 package specification and do not affect PCB layout or assembly.

Q: Which substitute part should I select for automotive applications?

A: Parts with AEC-Q200 rating are qualified for automotive use: ERJ-3EKF6982V, AC0603FR-0769K8L, CRCW060369K8FKEA, CRCW060369K8FKTA, and RMCF0603FT69K8. Among these, ROHS3-compliant options (all except CRCW060369K8FKTA) are preferred for regulatory compliance.

Q: Is ROHS3 compliance mandatory for my application?

A: ROHS3 compliance is required for products sold in the European Union and many other regulated markets. If your application is subject to such regulations, select only ROHS3-compliant parts. CRCW060369K8FKTA is non-compliant and should be avoided in regulated applications.

Q: What does Moisture Sensitivity Level (MSL) 1 mean?

A: MSL 1 indicates unlimited shelf life without moisture-related degradation. All listed parts carry MSL 1 rating, meaning they do not require special dry-pack storage or baking procedures prior to assembly.

Q: Can I mix different substitute parts in the same production run?

A: Yes. All parts meet identical electrical specifications and can be used interchangeably. However, mixing packaging formats (Tape & Reel vs. Cut Tape) may require separate handling procedures in automated assembly environments.