ELM 1-415 LED Standoff Equivalent & Substitute Parts

Part Overview

The ELM 1-415 is a T1 3/4 LED standoff manufactured by Bivar Inc., designed for vertical mounting applications. This component features a black PVC construction with a 0.415" (10.54mm) length specification. The part maintains Active product status and is RoHS3 compliant, making it suitable for current production environments. Substitute parts are identified when inventory constraints, lead time requirements, or specific application needs necessitate alternative components that maintain functional equivalence within the ELM 1 series.

Substiute Parts

ELM 1-415

Bivar Inc.In Stock: 818ELM 1-415 Datasheet

Current PartRFQ

ELM 1-11MM

Bivar Inc.In Stock: 1511ELM 1-11MM Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution within the ELM 1 series is determined by the following critical parameters:

Mandatory Matching Parameters:

• LED Type: T1 3/4 (physical form factor)
• Material: Black PVC (construction material)
• Series: ELM 1 (product family)
• Product Status: Active (current availability)
• RoHS Status: ROHS3 Compliant (regulatory requirement)

Allowable Variation Parameter:

• Length: Tolerance range of ±0.015" (0.38mm) from nominal specification

The ELM 1-415 (0.415" length) is substitutable with ELM 1-11MM (0.430" length) based on the length variation falling within acceptable mechanical tolerance for vertical mounting applications within the same series.

Parameter Comparison

Engineering Selection Recommendations

Primary Selection: ELM 1-415

• Use when exact 0.415" (10.54mm) length specification is required
• Current inventory: 763 Pcs New Original In Stock
• Meets all RoHS3 compliance requirements
• Active product status ensures continued availability

Substitute Selection: ELM 1-11MM

• Use when ELM 1-415 is unavailable or lead time is critical
• Length specification of 0.430" (10.92mm) represents a +0.015" (0.38mm) increase
• Current inventory: 1475 Pcs New Original In Stock
• Meets all RoHS3 compliance requirements
• Active product status ensures continued availability
• Substitution is valid only when the additional 0.015" length does not violate mechanical clearance or assembly constraints in the target application

Both parts maintain identical electrical and material properties within the ELM 1 series classification.

Frequently Asked Questions (FAQ)

Q: Can ELM 1-11MM be used as a direct replacement for ELM 1-415?

A: ELM 1-11MM is a parametric equivalent substitute when the length variation of +0.015" (0.38mm) does not conflict with mechanical constraints in your application. Both parts share identical LED type (T1 3/4), material (Black PVC), series designation (ELM 1), and compliance certifications (RoHS3). Verify that the increased length does not create interference with surrounding components or assembly fixtures.

Q: What is the significance of the length difference between these parts?

A: The ELM 1-415 measures 0.415" (10.54mm) while ELM 1-11MM measures 0.430" (10.92mm). This 0.015" (0.38mm) difference is the only parametric variation between the two parts. This variation is typical within mechanical tolerance ranges for LED standoff applications but must be evaluated against specific PCB layout and enclosure design requirements.

Q: Are both parts RoHS3 compliant?

A: Yes. Both ELM 1-415 and ELM 1-11MM carry RoHS3 Compliant certification and maintain Moisture Sensitivity Level 1 (Unlimited), making them suitable for equivalent use in regulated manufacturing environments.

Q: What is the packaging format for these parts?

A: Both ELM 1-415 and ELM 1-11MM are supplied in Bag packaging format. Inventory quantities are 763 Pcs and 1475 Pcs respectively, both listed as New Original In Stock.

Q: Can I use ELM 1-11MM if my design specifies ELM 1-415?

A: Substitution is permissible only when design documentation allows for the +0.015" length tolerance. Engineering review of mechanical drawings and assembly procedures is required to confirm that the increased standoff height does not create clearance violations or affect component alignment in the final assembly.