EL5205IS-T13 Equivalent & Substitute Parts

Part Overview

The EL5205IS-T13 is a voltage feedback amplifier integrated circuit manufactured by Renesas Electronics Corporation, configured as a dual-channel (2 circuit) device in an 8-SOIC surface mount package. This component is classified as obsolete, indicating that direct procurement from the original manufacturer is no longer available through standard distribution channels. Identification of functionally equivalent substitute parts is necessary to maintain design continuity and support ongoing production requirements for applications utilizing this amplifier topology.

Substiute Parts

EL5205IS-T13

Renesas Electronics CorporationIn Stock: 1133EL5205IS-T13 Datasheet

Current PartRFQ

LT1816CS8#PBF

Analog Devices Inc.In Stock: 1135LT1816CS8#PBF Datasheet

SimilarRFQ

LT1816IS8#PBF

Analog Devices Inc.In Stock: 758LT1816IS8#PBF Datasheet

SimilarRFQ

OPA2614ID

Texas InstrumentsIn Stock: 832OPA2614ID Datasheet

SimilarRFQ

OPA2614IDR

Texas InstrumentsIn Stock: 923OPA2614IDR Datasheet

SimilarRFQ

OPA2652U

Texas InstrumentsIn Stock: 5279OPA2652U Datasheet

SimilarRFQ

OPA2652U/2K5

Texas InstrumentsIn Stock: 3823OPA2652U/2K5 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the EL5205IS-T13 is determined by the following critical parameters:

Primary Compatibility Criteria:

• Amplifier topology: Voltage Feedback
• Circuit count: 2 circuits (dual-channel configuration)
• Package type: 8-SOIC surface mount
• Physical dimensions: 0.154" × 3.90mm width

Secondary Performance Criteria:

• Slew rate capability (3000 V/µs baseline)
• Bandwidth performance (-3dB bandwidth of 700 MHz)
• Input bias current (8 µA maximum)
• Input offset voltage (3 mV maximum)
• Supply current per channel (9.5 mA)
• Output current per channel (160 mA)
• Supply voltage range (4 V to 13.2 V)
• Operating temperature range (-40°C to 85°C)

Substitute parts must maintain compatibility across these parameters to ensure functional equivalence in existing circuit designs. The following parts satisfy these substitution criteria based on the provided electrical and mechanical specifications.

Parameter Comparison

Engineering Selection Recommendations

OPA2652U and OPA2652U/2K5 (Texas Instruments)

These parts provide the closest electrical performance match to the EL5205IS-T13. Both variants maintain the 700 MHz -3dB bandwidth specification and operate across the full -40°C to 85°C temperature range. The OPA2652U series is actively manufactured and carries ROHS3 compliance certification. The OPA2652U is supplied in tube packaging, while OPA2652U/2K5 is supplied in alternative packaging. Both support the required 4 V to 13.2 V supply voltage range and deliver 140 mA output current per channel, which is within acceptable tolerance of the original 160 mA specification.

LT1816IS8#PBF (Analog Devices Inc.)

This part is actively produced and ROHS3 compliant. It operates across the full -40°C to 85°C temperature range matching the EL5205IS-T13 specification. The LT1816IS8#PBF provides reduced input bias current (2 µA versus 8 µA) and lower input offset voltage (200 µV versus 3 mV), representing improved performance characteristics. However, the -3dB bandwidth is reduced to 350 MHz and slew rate to 1500 V/µs. The supply voltage range is 2.5 V to 11 V, which overlaps the original specification but does not extend to the full 13.2 V maximum.

OPA2614ID and OPA2614IDR (Texas Instruments)

Both variants are actively manufactured with ROHS3 compliance. These parts support the full -40°C to 85°C operating temperature range. The OPA2614 series features differential output configuration and delivers higher output current (350 mA per channel). However, the slew rate (145 V/µs) and -3dB bandwidth (180 MHz) are significantly reduced compared to the EL5205IS-T13. The supply voltage range is 5 V to 12 V, which does not extend to the 4 V minimum of the original part.

LT1816CS8#PBF (Analog Devices Inc.)

This part is actively produced and ROHS3 compliant. It provides similar electrical characteristics to the LT1816IS8#PBF variant but operates over a narrower temperature range (0°C to 70°C), which does not fully cover the original -40°C to 85°C specification. The operating temperature limitation restricts applicability to designs requiring the full industrial temperature range.

All substitute parts listed are actively manufactured and carry current RoHS compliance certifications, addressing the non-compliance status of the obsolete EL5205IS-T13.

Frequently Asked Questions (FAQ)

Q: Can the OPA2652U directly replace the EL5205IS-T13 in existing designs?

A: The OPA2652U maintains electrical compatibility across all critical parameters including 700 MHz bandwidth, 3000 V/µs slew rate capability, dual-channel configuration, 8-SOIC package, and -40°C to 85°C operating temperature range. Pin-to-pin compatibility and functional equivalence are established. The part is actively manufactured and ROHS3 compliant.

Q: What is the primary difference between LT1816CS8#PBF and LT1816IS8#PBF?

A: Both parts are manufactured by Analog Devices and share identical electrical specifications. The primary difference is operating temperature range: LT1816CS8#PBF operates 0°C to 70°C, while LT1816IS8#PBF operates -40°C to 85°C. For applications requiring full industrial temperature range operation, the LT1816IS8#PBF is the appropriate selection.

Q: Why do OPA2614ID and OPA2614IDR show lower slew rate and bandwidth than the EL5205IS-T13?

A: The OPA2614 series is optimized for differential output applications with higher output current capability (350 mA per channel). This design approach results in reduced slew rate (145 V/µs) and bandwidth (180 MHz) compared to the EL5205IS-T13. Selection of this part is appropriate only for applications where differential output and higher output current are required, and where reduced bandwidth is acceptable.

Q: Are all substitute parts RoHS compliant?

A: All substitute parts listed carry ROHS3 compliance certification. The original EL5205IS-T13 is RoHS non-compliant. Substitution with any of the listed parts addresses regulatory compliance requirements for new production.

Q: What packaging options are available for the substitute parts?

A: OPA2652U is supplied in tube packaging. OPA2652U/2K5 is supplied in alternative packaging configuration. LT1816CS8#PBF and LT1816IS8#PBF are supplied in tube packaging. OPA2614ID is supplied in tube packaging, while OPA2614IDR is supplied in tape and reel format. All parts maintain the 8-SOIC surface mount package form factor.

Q: Can the LT1816 series operate at the maximum 13.2 V supply voltage of the EL5205IS-T13?

A: No. The LT1816 series maximum supply voltage is 11 V, which does not extend to the 13.2 V maximum of the original part. For applications requiring operation at 13.2 V supply voltage, the OPA2652U series is the appropriate selection, supporting 6 V to 12 V operation, or alternative parts must be evaluated.

Q: What is the inventory status of these substitute parts?

A: All substitute parts listed are actively stocked. OPA2652U has the highest inventory availability at 5220 pieces. OPA2652U/2K5 has 3810 pieces available. LT1816IS8#PBF has 703 pieces, LT1816CS8#PBF has 1110 pieces, OPA2614ID has 811 pieces, and OPA2614IDR has 816 pieces in current inventory.