EGA.1B.306.CLL Equivalent & Substitute Parts

Part Overview

The EGA.1B.306.CLL is a 6-position circular connector receptacle manufactured by LEMO, featuring female sockets with solder cup termination. This connector is designed for panel mount applications with bulkhead rear side nut fastening and push-pull locking mechanism. The part is currently active in production with 744 units in stock. Substitute parts are identified when equivalent electrical and mechanical parameters align with the original specification, enabling component interchangeability in applications where the primary part becomes unavailable or when inventory constraints require alternative sourcing.

Substiute Parts

EGA.1B.306.CLL

LEMOIn Stock: 826EGA.1B.306.CLL Datasheet

Current PartRFQ

G11LAC-P06LFG0-0000

ODUIn Stock: 1109G11LAC-P06LFG0-0000 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

The substitute part G11LAC-P06LFG0-0000 (ODU MINI-SNAP® L series) qualifies as an equivalent based on the following alignment of critical parameters:

Matching Electrical Characteristics:

• 6-position connector configuration
• Female socket receptacle type
• Solder cup termination method
• Gold contact finish for mating surfaces
• Shielded design
• Current rating of 7A (substitute rated at 7.5A, exceeding minimum requirement)
• IP50 ingress protection rating

Matching Mechanical Characteristics:

• Panel mount configuration with bulkhead rear side nut
• Push-pull fastening mechanism
• Brass shell material with chrome finish
• PEEK insert material
• Orientation A

Compliance Alignment:

• ROHS3 compliant
• REACH unaffected status
• EAR99 ECCN classification
• Identical HTSUS code (8536.69.4020)

The substitute part operates within a narrower temperature range (-40°C ~ 120°C versus -55°C ~ 250°C), which represents a functional limitation for applications requiring the full temperature envelope of the original part.

Parameter Comparison

Engineering Selection Recommendations

Both parts maintain active production status and full ROHS3 compliance with REACH unaffected designation. The EGA.1B.306.CLL remains the primary specification for applications requiring the extended operating temperature range of -55°C to 250°C. The G11LAC-P06LFG0-0000 substitute is suitable for applications operating within the -40°C to 120°C temperature envelope, where the higher current rating of 7.5A provides additional margin. Both connectors carry identical regulatory classifications (EAR99, HTSUS 8536.69.4020) and meet the same environmental compliance standards. Selection between these parts depends on application temperature requirements and inventory availability.

Frequently Asked Questions (FAQ)

Q: Can G11LAC-P06LFG0-0000 be used in place of EGA.1B.306.CLL in all applications?

A: Substitution is valid only for applications operating within the temperature range of -40°C to 120°C. Applications requiring operation below -40°C or above 120°C must use the original EGA.1B.306.CLL specification.

Q: Are the physical dimensions and mounting interfaces identical?

A: Both connectors feature identical panel mount configurations with bulkhead rear side nut fastening and push-pull mechanisms. The 6-position solder cup receptacle interfaces are mechanically compatible.

Q: What is the difference in shell finish between the two parts?

A: The EGA.1B.306.CLL features chrome finish on brass, while the G11LAC-P06LFG0-0000 features chrome over nickel on brass. Both finishes provide equivalent corrosion protection and electrical performance for the specified applications.

Q: Does the higher current rating of the substitute part affect compatibility?

A: No. The 7.5A rating of the G11LAC-P06LFG0-0000 exceeds the 7A requirement of the original specification, providing additional safety margin without affecting electrical or mechanical compatibility.

Q: Are both parts suitable for industrial, medical, and military applications?

A: Both parts meet ROHS3 and REACH compliance requirements. The ODU substitute is documented for industrial, medical, military, and testing equipment applications. Application suitability depends on specific system requirements and qualification procedures.

Q: What is the moisture sensitivity level for each part?

A: The EGA.1B.306.CLL carries MSL 1 (Unlimited). The G11LAC-P06LFG0-0000 is classified as Not Applicable for MSL, indicating no moisture sensitivity constraints.