DTC114ECA-TP Equivalent & Substitute Parts

Part Overview

The DTC114ECA-TP is an active pre-biased NPN bipolar junction transistor (BJT) manufactured by Micro Commercial Co in SOT-23 surface mount packaging. This component is designed for general-purpose switching and amplification applications requiring integrated base bias resistors. The part is RoHS3 compliant and carries unlimited moisture sensitivity level (MSL 1) classification, making it suitable for standard manufacturing environments without special handling requirements.

Equivalent and substitute parts are necessary when the primary part number becomes unavailable, when alternative packaging formats are required for manufacturing compatibility, or when design specifications allow for functionally compatible alternatives from different manufacturers.

Key Parameters

Parameter	Value	Unit
Transistor Type	NPN - Pre-Biased	—
Maximum Collector Current (Ic)	100	mA
Collector-Emitter Breakdown Voltage (Max)	50	V
Base Resistor (R1)	10	kOhms
Emitter-Base Resistor (R2)	10	kOhms
DC Current Gain (hFE Min)	30	@ 5mA, 5V
Vce Saturation (Max)	300	mV @ 500µA, 10mA
Collector Cutoff Current (Max)	500	nA
Transition Frequency	250	MHz
Maximum Power Dissipation	200	mW
Mounting Type	Surface Mount	—
Package / Case	TO-236-3, SC-59, SOT-23-3	—
RoHS Status	ROHS3 Compliant	—
Moisture Sensitivity Level	1 (Unlimited)	—

Substitute Part Grouping Explanation

Substitution of the DTC114ECA-TP is determined by strict equivalence of the following critical parameters:

Mandatory Equivalence Parameters:

Transistor type: NPN - Pre-Biased
Maximum collector current: 100 mA
Collector-emitter breakdown voltage: 50 V
Base resistor (R1): 10 kOhms
Emitter-base resistor (R2): 10 kOhms
DC current gain minimum: 30 @ 5mA, 5V
Vce saturation maximum: 300 mV @ 500µA, 10mA
Collector cutoff current: 500 nA
Transition frequency: 250 MHz
Maximum power dissipation: 200 mW
Surface mount package compatibility

Packaging Considerations: Substitute parts are grouped by supplier device package format. The DTC114ECA-TP uses Cut Tape (CT) & Digi-Reel® packaging. Direct equivalents maintain identical electrical specifications and package type. Parts with different package formats (Tape & Reel, alternative SOT-23 variants, SC-59) are listed as compatible substitutes when all electrical parameters match or exceed the main part specifications.

Upgrade Classification: The DDTC115ECA-7-F is classified as an upgrade substitute due to higher base and emitter-base resistor values (100 kOhms vs. 10 kOhms) and higher DC current gain (82 vs. 30), which alter the bias network behavior and are not direct electrical equivalents.

Parameter Comparison

Part Number	Manufacturer	Ic (Max) mA	Vce(br) V	R1 kOhms	R2 kOhms	hFE Min	Vce Sat mV	Freq MHz	Power mW	Package	Packaging Type
DTC114ECA-TP	Micro Commercial Co	100	50	10	10	30	300	250	200	SOT-23-3	Cut Tape & Digi-Reel
DDTC114ECA-7-F	Diodes Incorporated	100	50	10	10	30	300	250	200	SOT-23-3	Tape & Reel
DTC114EKAT146	Rohm Semiconductor	50	50	10	10	30	300	250	200	SMT3	Cut Tape & Digi-Reel
MMUN2211LT1G	onsemi	100	50	10	10	35	250	—	246	SOT-23-3	Cut Tape & Digi-Reel
MMUN2211LT3G	onsemi	100	50	10	10	35	250	—	246	SOT-23-3	Cut Tape & Digi-Reel
MUN2211T1G	onsemi	100	50	10	10	35	250	—	230	SC-59	Cut Tape & Digi-Reel
MUN2211T3G	onsemi	100	50	10	10	35	250	—	230	SC-59	Cut Tape & Digi-Reel
SMMUN2211LT1G	onsemi	100	50	10	10	35	250	—	246	SOT-23-3	Tape & Reel
SMUN2211T1G	onsemi	100	50	10	10	35	250	—	230	SC-59	Tape & Reel
SMUN2211T3G	onsemi	100	50	10	10	35	250	—	230	SC-59	Tape & Reel
DDTC115ECA-7-F	Diodes Incorporated	100	50	100	100	82	300	250	200	SOT-23-3	Tape & Reel

Engineering Selection Recommendations

Direct Equivalents (Identical Electrical Specifications):

The DDTC114ECA-7-F from Diodes Incorporated is a direct electrical equivalent to the DTC114ECA-TP. Both parts share identical collector current, breakdown voltage, resistor values, current gain, saturation voltage, transition frequency, and power dissipation specifications. The primary difference is packaging format: DDTC114ECA-7-F is supplied in Tape & Reel format versus the Cut Tape & Digi-Reel format of the main part. Both are RoHS3 compliant with MSL 1 classification and active product status.

Compatible Substitutes (Equivalent or Superior Electrical Performance):

The onsemi MMUN2211LT1G, MMUN2211LT3G, MUN2211T1G, and MUN2211T3G parts meet or exceed the electrical requirements of the DTC114ECA-TP. These parts maintain the same collector current (100 mA), breakdown voltage (50 V), and resistor network (10 kOhms each). The onsemi parts demonstrate higher DC current gain (35 vs. 30 minimum) and lower saturation voltage (250 mV vs. 300 mV maximum), representing improved performance characteristics. Package variants include SOT-23-3 and SC-59 formats with both Cut Tape & Digi-Reel and Tape & Reel packaging options. All onsemi parts are RoHS3 compliant with MSL 1 classification and active product status.

The SMMUN2211LT1G, SMUN2211T1G, and SMUN2211T3G variants from onsemi carry automotive-grade qualification (AEC-Q101) and are supplied in Tape & Reel packaging. These parts are suitable for applications requiring automotive-level reliability while maintaining electrical equivalence to the main part.

Partial Compatibility (Reduced Current Rating):

The DTC114EKAT146 from Rohm Semiconductor is electrically compatible with the DTC114ECA-TP for all parameters except maximum collector current, which is rated at 50 mA versus 100 mA. This part is suitable for applications where the design current requirement does not exceed 50 mA. The part uses SMT3 package format and is supplied in Cut Tape & Digi-Reel packaging. RoHS3 compliance and MSL 1 classification are maintained.

Upgrade Substitute (Higher Bias Resistor Values):

The DDTC115ECA-7-F from Diodes Incorporated is classified as an upgrade substitute. This part features 100 kOhm base and emitter-base resistors (versus 10 kOhms in the DTC114ECA-TP) and a higher minimum DC current gain of 82 (versus 30). These differences alter the bias network behavior and input impedance characteristics. The DDTC115ECA-7-F is suitable only when the design specifically requires higher input impedance and different bias conditions. This part is RoHS3 compliant, MSL 1 classified, and in active product status.

Frequently Asked Questions (FAQ)

Q: Can the DDTC114ECA-7-F replace the DTC114ECA-TP in my design?

A: Yes. The DDTC114ECA-7-F is a direct electrical equivalent with identical collector current (100 mA), breakdown voltage (50 V), resistor values (10 kOhms each), current gain (30 minimum), saturation voltage (300 mV), and power dissipation (200 mW). The only difference is packaging format: Tape & Reel versus Cut Tape & Digi-Reel. Both parts are RoHS3 compliant and carry MSL 1 classification.

Q: What is the difference between the DTC114ECA-TP and the onsemi MMUN2211LT3G?

A: Both parts are electrically compatible with identical collector current (100 mA), breakdown voltage (50 V), and resistor network (10 kOhms each). The MMUN2211LT3G demonstrates superior performance with higher DC current gain (35 vs. 30 minimum) and lower saturation voltage (250 mV vs. 300 mV maximum). Package format differs: MMUN2211LT3G uses SOT-23-3 in Cut Tape & Digi-Reel format. Both are RoHS3 compliant with MSL 1 classification.

Q: Can I use the DTC114EKAT146 as a substitute?

A: The DTC114EKAT146 is compatible with the DTC114ECA-TP for all electrical parameters except maximum collector current. The DTC114EKAT146 is rated for 50 mA maximum collector current, while the DTC114ECA-TP is rated for 100 mA. Use the DTC114EKAT146 only if your design current requirement does not exceed 50 mA. All other specifications (breakdown voltage, resistor values, current gain, saturation voltage) are identical.

Q: What does the "S" prefix in SMMUN2211LT1G indicate?

A: The "S" prefix indicates automotive-grade qualification to AEC-Q101 standard. The SMMUN2211LT1G is electrically equivalent to the standard MMUN2211LT1G but carries automotive-level reliability certification. This part is suitable for automotive applications requiring AEC-Q101 qualification while maintaining all electrical equivalence to the DTC114ECA-TP.

Q: Why should I consider the DDTC115ECA-7-F?

A: The DDTC115ECA-7-F is an upgrade substitute with different bias network characteristics. It features 100 kOhm base and emitter-base resistors (versus 10 kOhms) and higher DC current gain (82 vs. 30 minimum). Use this part only when your design specifically requires higher input impedance and different bias conditions. It is not a direct replacement for general-purpose applications.

Q: Are all substitute parts RoHS3 compliant?

A: Yes. All parts listed—DTC114ECA-TP, DDTC114ECA-7-F, DTC114EKAT146, MMUN2211LT1G, MMUN2211LT3G, MUN2211T1G, MUN2211T3G, SMMUN2211LT1G, SMUN2211T1G, SMUN2211T3G, and DDTC115ECA-7-F—are RoHS3 compliant with MSL 1 (Unlimited) moisture sensitivity level classification.

Q: What is the difference between Cut Tape & Digi-Reel and Tape & Reel packaging?

A: Cut Tape & Digi-Reel format provides individual component strips on tape with reel compatibility for automated handling. Tape & Reel format supplies components on continuous tape wound on reels for high-volume automated assembly. Both formats are surface mount compatible. Selection depends on manufacturing equipment and volume requirements.

Q: Can I use MUN2211T1G or MUN2211T3G if my PCB layout requires SC-59 package?

A: Yes. The MUN2211T1G and MUN2211T3G are supplied in SC-59 package format and are electrically compatible with the DTC114ECA-TP. Both parts maintain 100 mA collector current, 50 V breakdown voltage, and 10 kOhm resistor values. The SC-59 package is mechanically equivalent to SOT-23-3 and can be used interchangeably in designs that accommodate this package format.

Q: Are there any frequency differences between substitute parts?

A: The DTC114ECA-TP and DDTC114ECA-7-F both specify 250 MHz transition frequency. The onsemi parts (MMUN2211 and MUN2211 series) do not specify transition frequency in the provided data. For applications requiring guaranteed 250 MHz transition frequency, use DTC114ECA-TP or DDTC114ECA-7-F.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message