DMN3016LFDF-13 Equivalent & Substitute Parts

Part Overview

The DMN3016LFDF-13 is an N-Channel MOSFET manufactured by Diodes Incorporated, rated for 30V drain-to-source voltage with 12A continuous drain current at 25°C. This device is housed in a 6-UDFN surface mount package with exposed pad and is classified as Active product status. The part is ROHS3 compliant with MSL 1 (Unlimited) moisture sensitivity rating.

Substitute parts are identified when equivalent electrical performance and mechanical compatibility are maintained across the specified parameter set. Alternative sources or packaging variants may be required due to inventory availability, supply chain considerations, or design revision requirements.

Substiute Parts

DMN3016LFDF-13

Diodes IncorporatedIn Stock: 1114DMN3016LFDF-13 Datasheet

Current PartRFQ

DMN3016LFDF-7

Diodes IncorporatedIn Stock: 10010DMN3016LFDF-7 Datasheet

Parametric EquivalentRFQ

PMPB11EN,115

Nexperia USA Inc.In Stock: 85743PMPB11EN,115 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility is determined by matching the following critical electrical and mechanical parameters:

Electrical Equivalence Criteria:

• Drain to Source Voltage (Vdss): 30V minimum
• Continuous Drain Current (Id) @ 25°C: 12A minimum
• On-State Resistance (Rds On): 12mOhm maximum @ specified conditions
• Gate Threshold Voltage (Vgs(th)): 2V maximum @ 250µA
• Gate Charge (Qg): 25.1nC maximum @ 10V
• Maximum Gate Voltage (Vgs): ±20V minimum
• Input Capacitance (Ciss): 1415pF maximum @ specified voltage
• Power Dissipation: 2.02W (Ta) minimum
• Operating Temperature Range: -55°C to 150°C (TJ)

Mechanical Compatibility Criteria:

• Package Type: 6-UDFN Exposed Pad
• Mounting Type: Surface Mount
• Supplier Device Package: U-DFN2020-6 (Type F) or equivalent footprint

Compliance Requirements:

• RoHS3 Compliant
• MSL 1 (Unlimited)
• REACH Unaffected
• ECCN: EAR99

Parameter Comparison

Engineering Selection Recommendations

DMN3016LFDF-7 (Parametric Equivalent)

The DMN3016LFDF-7 is a direct parametric equivalent to the DMN3016LFDF-13. Both parts are manufactured by Diodes Incorporated and share identical electrical specifications across all critical parameters: 30V Vdss, 12A continuous drain current, 12mOhm Rds On, and matching gate charge characteristics. The package footprint, mounting type, and compliance certifications are identical. This substitute is suitable for direct replacement in applications where the DMN3016LFDF-13 is specified. The primary distinction is packaging variant (Tape & Reel designation), with the DMN3016LFDF-7 offering higher inventory availability (9900 Pcs vs. 1101 Pcs).

PMPB11EN,115 (Manufacturer Recommended Substitute)

The PMPB11EN,115 is a manufacturer-recommended substitute manufactured by Nexperia USA Inc. This part maintains compatibility across voltage ratings (30V Vdss), gate threshold voltage (2V @ 250µA), maximum gate voltage (±20V), and operating temperature range (-55°C to 150°C). The package type remains 6-UDFN Exposed Pad with surface mount configuration.

Key parameter differences exist in continuous drain current and on-state resistance. The PMPB11EN,115 is rated for 9A continuous drain current at 25°C (versus 12A for the main part) and exhibits 14.5mOhm Rds On at 9A, 10V (versus 12mOhm at 11A, 10V for the main part). Gate charge is lower at 20.6nC @ 10V, and input capacitance is reduced to 840pF @ 10V. Power dissipation is specified as 1.7W (Ta) and 12.5W (Tc).

This substitute is applicable in designs where the 9A current rating is sufficient for the application requirements. The reduced gate charge and input capacitance may provide switching performance advantages in certain circuit topologies. Inventory availability is significantly higher (85663 Pcs).

All substitute parts maintain Active product status, ROHS3 compliance, MSL 1 (Unlimited) rating, REACH Unaffected status, and EAR99 ECCN classification.

Frequently Asked Questions (FAQ)

Q: Can DMN3016LFDF-7 be used as a direct replacement for DMN3016LFDF-13?

A: Yes. The DMN3016LFDF-7 is a parametric equivalent with identical electrical specifications and package configuration. Both parts are manufactured by Diodes Incorporated and share the same base product number (DMN3016). The parts are interchangeable from an electrical and mechanical standpoint.

Q: What are the limitations of using PMPB11EN,115 as a substitute?

A: The PMPB11EN,115 has a lower continuous drain current rating of 9A compared to the 12A rating of the DMN3016LFDF-13. Applications requiring continuous drain currents above 9A at 25°C cannot use this substitute. The on-state resistance is also higher at 14.5mOhm versus 12mOhm. Verify that the application's maximum current requirement does not exceed 9A before selecting this substitute.

Q: Are the package footprints identical between all three parts?

A: All three parts use 6-UDFN Exposed Pad packages with surface mount configuration. The DMN3016LFDF-13 and DMN3016LFDF-7 use U-DFN2020-6 (Type F) supplier device packages, while the PMPB11EN,115 uses DFN2020MD-6. Both package designations are compatible with the same PCB footprint for 6-UDFN Exposed Pad devices.

Q: Do all substitute parts meet the same compliance requirements?

A: Yes. All three parts are ROHS3 compliant, have MSL 1 (Unlimited) moisture sensitivity ratings, are REACH Unaffected, and carry EAR99 ECCN classification. Compliance certifications are equivalent across all options.

Q: What is the difference between the packaging variants (Tape & Reel vs. Cut Tape)?

A: Tape & Reel (TR) and Cut Tape (CT) & Digi-Reel® refer to supply format and quantity per reel. Both are surface mount packaging formats suitable for automated assembly. The electrical and mechanical specifications of the component remain unchanged. Selection between these formats depends on production volume and assembly equipment compatibility.

Q: Can PMPB11EN,115 be used in high-current applications?

A: The PMPB11EN,115 is rated for 9A continuous drain current at 25°C. Applications requiring sustained currents above 9A must use the DMN3016LFDF-13 or DMN3016LFDF-7, both rated for 12A. Exceeding the rated current specification will result in thermal stress and potential device failure.

Q: Are there differences in switching characteristics between the substitutes?

A: Yes. The PMPB11EN,115 has lower gate charge (20.6nC vs. 25.1nC) and lower input capacitance (840pF vs. 1415pF). These differences may affect switching speed and gate drive requirements. Circuits with tight switching timing constraints should evaluate the impact of these parameter differences before substitution.

Q: What is the operating temperature range for all parts?

A: All three parts operate across the same temperature range: -55°C to 150°C (TJ). Thermal management and derating considerations are equivalent across all options.