CZP2BFTTE601P Equivalent & Substitute Parts

Part Overview

The CZP2BFTTE601P is a 1206 surface mount ferrite bead manufactured by KOA Speer Electronics, Inc., designed for power line filtering applications. This component provides 600 Ohms impedance at 100 MHz with a maximum current rating of 1A and 200mOhm DC resistance. The part is active in production status and fully compliant with ROHS3 and REACH regulations, making it suitable for modern electronic assemblies requiring EMI suppression on power distribution networks.

Equivalent and substitute parts are identified to support procurement flexibility, inventory management, and supply chain continuity for applications requiring ferrite bead filtering with matching electrical and mechanical specifications.

Substiute Parts

CZP2BFTTE601P

KOA Speer Electronics, Inc.In Stock: 3793CZP2BFTTE601P Datasheet

Current PartRFQ

BLM31PG601SN1L

Murata ElectronicsIn Stock: 521871BLM31PG601SN1L Datasheet

SimilarRFQ

2512066017Y1

Fair-Rite Products Corp.In Stock: 333532512066017Y1 Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the CZP2BFTTE601P are identified based on strict electrical and mechanical compatibility criteria. The primary substitution parameters are:

• Impedance matching at 100 MHz (600 Ohms)
• Package compatibility (1206 / 3216 Metric)
• Operating temperature range (-55°C ~ 125°C)
• Surface mount configuration
• Single-line ferrite bead topology
• RoHS3 and REACH compliance status

Two substitute parts meet these criteria with variations in current rating and DC resistance that remain within acceptable operating parameters for power line filtering applications.

Parameter Comparison

Engineering Selection Recommendations

BLM31PG601SN1L (Murata Electronics) is the primary substitute for CZP2BFTTE601P. This part maintains identical impedance and package specifications while offering improved electrical performance with 1.5A current rating and 80mOhm DC resistance. Both parts are active in production status and fully compliant with ROHS3 and REACH requirements. The Murata part is suitable for direct replacement in power line filtering applications where the enhanced current capacity and reduced DC resistance provide operational margin.

2512066017Y1 (Fair-Rite Products Corp.) provides parametric equivalence with matching impedance, current rating, and DC resistance to the original part. However, this part is classified as a signal line ferrite bead rather than power line, reflecting a difference in application design intent. This part remains electrically compatible for 1A applications and maintains full compliance certifications. Selection between the KOA and Fair-Rite parts depends on application-specific filtering requirements and supply chain availability.

Frequently Asked Questions (FAQ)

Q: Can BLM31PG601SN1L replace CZP2BFTTE601P in all applications?

A: Yes, for applications operating at or below 1A. The Murata part provides superior electrical characteristics with lower DC resistance and higher current rating, making it suitable for direct substitution in power line filtering circuits. Both parts share identical impedance, package, and temperature specifications.

Q: What is the difference between power line and signal line ferrite beads?

A: Power line ferrite beads are optimized for higher current applications and power distribution networks. Signal line ferrite beads are designed for lower current signal paths. The 2512066017Y1 is classified as signal line but maintains electrical compatibility with the original power line specification at 1A operation.

Q: Are all three parts pin-compatible?

A: Yes. All three parts use the 1206 (3216 Metric) surface mount package with identical footprint dimensions (0.126" L x 0.063" W / 3.20mm x 1.60mm) and maximum height (0.051" / 1.30mm). They are mechanically and electrically interchangeable at the PCB level.

Q: Do packaging differences affect substitution?

A: Packaging format (Tape & Reel vs. Cut Tape) affects procurement and assembly logistics but does not impact electrical or mechanical compatibility. Component performance and PCB mounting are identical regardless of packaging type.

Q: Are all substitute parts RoHS and REACH compliant?

A: Yes. All three parts are ROHS3 compliant and REACH unaffected, meeting current regulatory requirements for electronic component manufacturing and use.