CM07FD153JO3 Equivalent & Substitute Parts

Part Overview

The CM07FD153JO3 is a 0.015 µF mica capacitor rated for 500 V operation in a radial through-hole configuration, manufactured by Cornell Dubilier Electronics (CDE). This component is classified as Active product status with general-purpose application capability. Mica capacitors of this specification are utilized in high-reliability circuits requiring stable capacitance over temperature and frequency ranges. Substitute parts may be required due to inventory constraints, manufacturing discontinuation, or compliance requirement alignment with updated regulatory standards.

Substiute Parts

CM07FD153JO3

Cornell Dubilier Electronics (CDE)In Stock: 840CM07FD153JO3 Datasheet

Current PartRFQ

CD30FD153JO3F

Cornell Dubilier Electronics (CDE)In Stock: 997CD30FD153JO3F Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the CM07FD153JO3 is determined by strict equivalence across the following critical parameters:

Electrical Parameters (Non-negotiable):

• Capacitance value: 0.015 µF
• Tolerance: ±5%
• Voltage rating: 500 V
• Dielectric material: Mica

Mechanical Parameters (Non-negotiable):

• Mounting type: Through Hole
• Package configuration: Radial
• Lead spacing: 0.437" (11.10 mm)

Environmental Parameters (Non-negotiable):

• Operating temperature range: -55°C to 125°C

The substitute part CD30FD153JO3F meets all electrical, mechanical, and environmental criteria. Both components are manufactured by Cornell Dubilier Electronics and share identical functional specifications. The primary distinction lies in product series designation (CM07 versus CD30) and regulatory compliance status.

Parameter Comparison

Engineering Selection Recommendations

CM07FD153JO3 Selection Criteria:

• Applications where RoHS non-compliance is acceptable or not required
• Existing inventory availability (751 pcs in stock)
• Legacy system designs with established component qualification

CD30FD153JO3F Selection Criteria:

• Applications requiring ROHS3 compliance
• Applications requiring REACH compliance (REACH Unaffected status)
• New designs subject to updated regulatory requirements
• Higher inventory availability (906 pcs in stock)

Both components are Active product status and share identical electrical, mechanical, and environmental specifications. The CD30FD153JO3F represents the compliance-aligned alternative within the same manufacturer's product portfolio. Selection between these parts should be based on regulatory compliance requirements applicable to the end application and system design phase.

Frequently Asked Questions (FAQ)

Q: Can CM07FD153JO3 and CD30FD153JO3F be used interchangeably on the same PCB?

A: Yes. Both components share identical capacitance (0.015 µF), tolerance (±5%), voltage rating (500 V), lead spacing (0.437"), and physical dimensions. PCB footprints designed for either part will accommodate the other without modification.

Q: What is the difference between these two part numbers?

A: The primary differences are product series designation (CM07 versus CD30) and regulatory compliance status. The CD30FD153JO3F is ROHS3 compliant and REACH unaffected, while the CM07FD153JO3 is RoHS non-compliant and REACH affected. All electrical and mechanical specifications are identical.

Q: Which part should be selected for new designs?

A: Selection depends on regulatory requirements. For applications subject to RoHS3 or REACH compliance mandates, the CD30FD153JO3F is the appropriate choice. For applications without such requirements, either part is functionally equivalent.

Q: Are there any temperature or frequency limitations that differ between these parts?

A: No. Both components operate across the identical temperature range (-55°C to 125°C) and utilize mica dielectric material, which provides stable performance across frequency ranges typical for general-purpose applications.

Q: What is the lead spacing specification, and why is it important?

A: Lead spacing is 0.437" (11.10 mm) for both parts. This dimension determines PCB hole pattern compatibility. Substitution is only valid when lead spacing matches the existing PCB design.

Q: Can these mica capacitors be soldered using standard through-hole assembly processes?

A: Both components are through-hole mounted radial capacitors. Assembly compatibility depends on PCB design specifications and soldering process parameters, which are outside the scope of component equivalence.