CLC2010ISO8MTR Equivalent & Substitute Parts

Part Overview

The CLC2010ISO8MTR is a voltage feedback amplifier integrated circuit manufactured by MaxLinear, Inc., configured as a dual-channel (2 circuit) rail-to-rail operational amplifier in an 8-SOIC surface mount package. This device is classified as obsolete product status, necessitating identification of active equivalent alternatives for new designs and production continuity. The CLC2010ISO8MTR operates across a 2.5V to 5.5V supply range with a slew rate of 9V/µs and gain bandwidth product of 4 MHz, designed for general-purpose voltage feedback amplification applications requiring compact form factors and low power consumption.

Substiute Parts

CLC2010ISO8MTR

MaxLinear, Inc.In Stock: 860CLC2010ISO8MTR Datasheet

Current PartRFQ

MAX4416ESA+

Analog Devices Inc./Maxim IntegratedIn Stock: 995MAX4416ESA+ Datasheet

MFR RecommendedRFQ

MAX4416ESA+T

Analog Devices Inc./Maxim IntegratedIn Stock: 672MAX4416ESA+T Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the CLC2010ISO8MTR is determined by strict alignment of the following electrical and mechanical parameters:

Primary Substitution Criteria:

• Amplifier Type: Voltage Feedback (required match)
• Number of Circuits: 2 channels (required match)
• Output Type: Rail-to-Rail (required match)
• Package / Case: 8-SOIC form factor (required match)
• Mounting Type: Surface Mount (required match)
• Voltage - Supply Span: Minimum 2.5V, Maximum 5.5V (required compatibility)
• Operating Temperature Range: -40°C ~ 85°C (required match)

The substitute parts identified—MAX4416ESA+ and MAX4416ESA+T—satisfy all primary substitution criteria. Both are dual-channel voltage feedback amplifiers with rail-to-rail output in 8-SOIC surface mount packages, operating across the same supply voltage and temperature ranges as the CLC2010ISO8MTR. The distinction between MAX4416ESA+ and MAX4416ESA+T is packaging format: tube versus tape & reel, respectively. Both variants are manufactured by Analog Devices Inc./Maxim Integrated and maintain active product status, ensuring long-term availability and support.

Parameter Comparison

Engineering Selection Recommendations

The CLC2010ISO8MTR is classified as obsolete product status. For new designs and production continuity, the MAX4416ESA+ or MAX4416ESA+T are the designated manufacturer-recommended substitutes. Both alternatives are active products manufactured by Analog Devices Inc./Maxim Integrated, ensuring ongoing availability, technical support, and compliance with current regulatory standards.

Selection between MAX4416ESA+ and MAX4416ESA+T:

• MAX4416ESA+: Supplied in tube packaging. Select this variant for lower-volume applications, prototype development, or when tube packaging aligns with assembly processes.

• MAX4416ESA+T: Supplied in tape & reel (TR) packaging. Select this variant for high-volume production runs and automated pick-and-place assembly operations.

Both variants are ROHS3 compliant and REACH unaffected, meeting modern environmental and regulatory requirements. The substitute parts demonstrate superior electrical performance compared to the obsolete CLC2010ISO8MTR, including higher slew rate (200V/µs versus 9V/µs), increased bandwidth (400 MHz versus 3.4 MHz), and higher output current capability (75 mA versus 4 mA per channel). These enhancements provide design flexibility for applications requiring higher-speed signal processing or increased load-driving capability.

The minimum supply voltage specification differs slightly (2.7V for MAX4416 versus 2.5V for CLC2010ISO8MTR); applications operating below 2.7V require circuit redesign or alternative component selection.

Frequently Asked Questions (FAQ)

Q: Can MAX4416ESA+ and MAX4416ESA+T be used interchangeably in the same circuit?

A: Yes. Both parts are electrically and mechanically identical. The only difference is packaging format: MAX4416ESA+ uses tube packaging, while MAX4416ESA+T uses tape & reel packaging. Selection depends on assembly method and volume requirements, not circuit functionality.

Q: What is the primary reason for substituting CLC2010ISO8MTR?

A: The CLC2010ISO8MTR is classified as obsolete product status. Manufacturer support, technical documentation, and long-term availability cannot be guaranteed. The MAX4416ESA+ and MAX4416ESA+T are active products with full manufacturer support and assured supply continuity.

Q: Are the substitute parts pin-compatible with CLC2010ISO8MTR?

A: Both substitute parts use the same 8-SOIC package form factor (0.154", 3.90mm width) as the CLC2010ISO8MTR. Pin compatibility is confirmed by identical package specifications. PCB layout modifications are not required for package-level substitution.

Q: What are the key electrical differences between CLC2010ISO8MTR and MAX4416ESA+/MAX4416ESA+T?

A: The substitute parts offer superior performance: slew rate increases from 9V/µs to 200V/µs, bandwidth increases from 3.4 MHz to 400 MHz, and output current per channel increases from 4 mA to 75 mA. Input bias current decreases from 90 nA to 1.3 µA, and input offset voltage decreases from 1 mV to 0.5 mV. These improvements enable higher-speed applications and increased load-driving capability.

Q: Is the minimum supply voltage specification compatible?

A: The CLC2010ISO8MTR operates at minimum 2.5V, while MAX4416ESA+/MAX4416ESA+T operate at minimum 2.7V. Applications requiring operation below 2.7V cannot use the substitute parts without circuit modification. For applications operating at 2.7V or higher, the substitute parts are fully compatible.

Q: Are the substitute parts compliant with current environmental regulations?

A: Yes. Both MAX4416ESA+ and MAX4416ESA+T are ROHS3 compliant and REACH unaffected, meeting current environmental and regulatory requirements for electronic components in most jurisdictions.

Q: Which packaging format should be selected for high-volume production?

A: MAX4416ESA+T (tape & reel packaging) is recommended for high-volume production runs. Tape & reel format is optimized for automated pick-and-place assembly equipment, reducing handling time and improving production efficiency. Tube packaging (MAX4416ESA+) is suitable for lower-volume applications or manual assembly processes.