AP7365-10YRG-13 Equivalent & Substitute Parts

Part Overview

The AP7365-10YRG-13 is a linear voltage regulator IC from Diodes Incorporated designed for positive fixed 1V output applications. This Surface Mount device delivers 600mA output current with a maximum dropout voltage of 0.6V at rated load. The part is actively produced and widely used in power management circuits requiring low-voltage regulation with integrated over-current and over-temperature protection. Substitute parts are identified when equivalent electrical performance and mechanical compatibility are maintained across the specified parameter range.

Substiute Parts

AP7365-10YRG-13

Diodes IncorporatedIn Stock: 9477AP7365-10YRG-13 Datasheet

Current PartRFQ

AP7365-10YG-13

Diodes IncorporatedIn Stock: 3517AP7365-10YG-13 Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the AP7365-10YRG-13 is determined by strict equivalence across the following critical parameters:

• Output voltage configuration (Positive, Fixed 1V)
• Output current capability (600mA)
• Maximum input voltage (6V)
• Dropout voltage specification (0.6V @ 600mA)
• Quiescent current (80 µA)
• PSRR performance (65dB at 1kHz)
• Protection features (Over Current, Over Temperature)
• Operating temperature range (-40°C ~ 85°C)
• Package type (TO-243AA)
• Mounting configuration (Surface Mount)
• Regulatory compliance (ROHS3, REACH Unaffected)

The AP7365-10YG-13 meets all these criteria and is classified as a parametric equivalent. The primary distinction between the main part and substitute is the supplier device package designation (SOT-89R-3 versus SOT-89-3), which represents a packaging variation within the same TO-243AA case family.

Parameter Comparison

Engineering Selection Recommendations

Both AP7365-10YRG-13 and AP7365-10YG-13 are Active status products from Diodes Incorporated with full ROHS3 compliance and REACH Unaffected designation. Selection between these parts is based on packaging availability and supply chain requirements rather than electrical performance differentiation. The AP7365-10YRG-13 is available in higher inventory (9400 Pcs) compared to AP7365-10YG-13 (3455 Pcs). Both parts maintain identical electrical specifications, protection features, and operating characteristics across the specified temperature range. PCB layout and thermal management considerations remain consistent between variants due to identical TO-243AA case geometry.

Frequently Asked Questions (FAQ)

Q: Can AP7365-10YG-13 be used as a direct replacement for AP7365-10YRG-13?

A: Yes. Both parts are electrically and mechanically equivalent. The difference in supplier device package designation (SOT-89R-3 versus SOT-89-3) does not affect circuit performance or PCB compatibility, as both conform to the TO-243AA case standard.

Q: What is the difference between SOT-89R-3 and SOT-89-3 packaging?

A: Both designations refer to variations within the TO-243AA package family. The "R" designation typically indicates tape and reel packaging format. Both variants maintain identical pin configuration, pitch, and thermal characteristics required for this application.

Q: Are there any compliance or certification differences between these parts?

A: No. Both AP7365-10YRG-13 and AP7365-10YG-13 carry identical ROHS3 compliance, REACH Unaffected status, and MSL rating of 1 (Unlimited). Regulatory and environmental certifications are equivalent.

Q: What parameters must remain constant for substitution?

A: Output voltage (1V fixed), output current (600mA), input voltage rating (6V max), dropout voltage (0.6V @ 600mA), quiescent current (80 µA), PSRR (65dB at 1kHz), operating temperature range (-40°C to 85°C), and protection features (over-current and over-temperature) must all match for valid substitution.

Q: Does the higher inventory of AP7365-10YRG-13 affect performance?

A: No. Inventory levels reflect supply availability only and do not impact electrical performance, reliability, or specifications. Both parts meet identical performance criteria.