AP2411AM8-13 Equivalent & Substitute Parts

Part Overview

The AP2411AM8-13 is a Power Switch/Driver IC from Diodes Incorporated, configured as a 1:1 P-Channel USB Switch with 2A output capacity. This component operates in the 2.7V to 5.5V load voltage range and integrates load discharge, slew rate control, and comprehensive fault protection including current limiting, over-temperature, reverse current, and UVLO monitoring.

The AP2411AM8-13 is classified as Obsolete. Equivalent and substitute parts are available from the same manufacturer with Active product status, ensuring continued design support and supply chain reliability.

Substiute Parts

AP2411AM8-13

Diodes IncorporatedIn Stock: 1109AP2411AM8-13 Datasheet

Current PartRFQ

AP2401AM8-13

Diodes IncorporatedIn Stock: 10146AP2401AM8-13 Datasheet

DirectRFQ

AP2301AM8-13

Diodes IncorporatedIn Stock: 7876AP2301AM8-13 Datasheet

Parametric EquivalentRFQ

AP2311M8G-13

Diodes IncorporatedIn Stock: 300508AP2311M8G-13 Datasheet

Parametric EquivalentRFQ

AP2511AM8-13

Diodes IncorporatedIn Stock: 25423AP2511AM8-13 Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the AP2411AM8-13 is determined by the following critical parameters:

• Switch Type & Output Configuration: USB Switch, High Side, P-Channel, 1:1 ratio
• Electrical Performance: 2A maximum output current, 70mOhm typical on-resistance, 2.7V–5.5V load voltage range
• Fault Protection: Current limiting, over-temperature, reverse current, and UVLO protection
• Package Compatibility: 8-MSOP surface mount package with identical pinout and thermal characteristics
• Environmental Compliance: ROHS3 compliance and MSL 1 rating

All substitute parts listed maintain these core parameters. The primary distinction among substitutes is the Input Type (Inverting vs. Non-Inverting logic) and Product Status (Active vs. Obsolete).

Parameter Comparison

Engineering Selection Recommendations

For Active Product Status Requirement: The AP2411AM8-13 is Obsolete. Direct substitutes with Active product status are AP2401AM8-13, AP2301AM8-13, AP2311M8G-13, and AP2511AM8-13. All maintain identical electrical specifications, package geometry, and fault protection architecture.

For Non-Inverting Input Logic: If the design requires Non-Inverting input type, select from AP2301AM8-13, AP2311M8G-13, or AP2511AM8-13. These parts maintain the same input logic as the AP2411AM8-13.

For Inverting Input Logic: The AP2401AM8-13 provides an Inverting input alternative while maintaining all other electrical and mechanical parameters.

For Supply Chain Continuity: AP2311M8G-13 offers the highest inventory availability (300400 Pcs), followed by AP2511AM8-13 (25400 Pcs) and AP2401AM8-13 (10100 Pcs). All parts are ROHS3 compliant with MSL 1 rating, supporting long-term procurement strategies.

Frequently Asked Questions (FAQ)

Q: Can AP2401AM8-13 replace AP2411AM8-13 directly? A: AP2401AM8-13 is electrically and mechanically compatible with AP2411AM8-13. The primary difference is Input Type: AP2401AM8-13 uses Inverting logic while AP2411AM8-13 uses Non-Inverting logic. Circuit-level verification of input signal polarity is required before substitution.

Q: What is the difference between AP2301AM8-13 and AP2311M8G-13? A: Both parts are parametric equivalents with identical electrical specifications and Non-Inverting input type. The primary distinction is packaging designation and inventory availability. AP2311M8G-13 has significantly higher stock levels (300400 Pcs vs. 7800 Pcs).

Q: Are all substitute parts pin-compatible with AP2411AM8-13? A: Yes. All substitute parts use the 8-MSOP package with identical pinout and thermal characteristics (0.118", 3.00mm Width). PCB layout and footprint modifications are not required.

Q: Which substitute part should be selected for new designs? A: For new designs, select from Active status parts: AP2301AM8-13, AP2311M8G-13, or AP2511AM8-13 (Non-Inverting input) or AP2401AM8-13 (Inverting input). All provide long-term design support and supply chain reliability.

Q: Do all substitute parts meet the same environmental and compliance standards? A: Yes. All substitute parts are ROHS3 compliant with MSL 1 (Unlimited) rating, identical operating temperature range (-40°C ~ 85°C), and equivalent fault protection (current limiting, over-temperature, reverse current, UVLO).

Q: What is the impact of selecting AP2511AM8-13 over other substitutes? A: AP2511AM8-13 is available in Cut Tape (CT) & Digi-Reel® packaging, offering alternative supply chain options. Electrical and mechanical specifications remain identical to other Non-Inverting alternatives.