AP2192MPG-13 Equivalent & Substitute Parts

Part Overview

The AP2192MPG-13 is an active power switch integrated circuit manufactured by Diodes Incorporated, classified as a Power Management (PMIC) device. This component functions as a 2-channel USB power switch with 1.5A maximum output current per channel, designed for high-side switching applications using P-Channel output configuration. The device is currently in active product status with 2200 units available in inventory.

Substitute parts are identified when equivalent functional performance can be achieved through alternative manufacturers' components that maintain compatibility across critical electrical parameters, mechanical packaging, and operational specifications. Substitution becomes necessary due to supply chain considerations, inventory availability, or design flexibility requirements.

Substiute Parts

AP2192MPG-13

Diodes IncorporatedIn Stock: 2283AP2192MPG-13 Datasheet

Current PartRFQ

TPS2062QDGNRQ1

Texas InstrumentsIn Stock: 3840TPS2062QDGNRQ1 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the AP2192MPG-13 are identified based on the following critical parameters that determine functional equivalence:

Electrical Compatibility Criteria:

• Number of outputs: 2 channels required
• Input:Output ratio: 1:2 configuration
• Output configuration: High-side switching topology
• Voltage range: 2.7V to 5.5V load voltage compatibility
• Interface type: On/Off control logic
• Fault protection: Current limiting, over-temperature, and UVLO protection

Mechanical Compatibility Criteria:

• Package type: 8-MSOP or 8-HVSSOP with exposed pad
• Mounting type: Surface mount
• Physical footprint: 0.118" width, 3.00mm standard

Operational Criteria:

• Product status: Active
• RoHS compliance: ROHS3 Compliant
• REACH status: REACH Unaffected

The TPS2062QDGNRQ1 qualifies as a substitute based on matching the 1:2 dual-output topology, high-side configuration, compatible voltage range, and equivalent package footprint. Differences in output type (N-Channel vs. P-Channel), maximum current rating (1A vs. 1.5A), and operating temperature range represent design trade-offs that must be evaluated for specific application requirements.

Parameter Comparison

Engineering Selection Recommendations

AP2192MPG-13 Selection Criteria: The AP2192MPG-13 is the primary component choice when P-Channel output topology is required for the application circuit design. This device supports the full 1.5A maximum output current specification and operates across the -40°C to 85°C temperature range. The component includes reverse current protection in addition to standard fault protection features. ROHS3 compliance and MSL Level 1 rating indicate unlimited shelf life storage capability.

TPS2062QDGNRQ1 Selection Criteria: The TPS2062QDGNRQ1 serves as a substitute when N-Channel output configuration is compatible with the application design. This device operates across an extended temperature range (-40°C to 125°C) and includes automotive-grade qualification (AEC-Q100). The lower typical on-resistance (70mOhm vs. 85mOhm) provides reduced power dissipation characteristics. The maximum output current is limited to 1A per channel, which represents a design constraint for applications requiring the full 1.5A capability of the main part. MSL Level 2 rating requires controlled storage conditions with a 1-year shelf life limit.

Both components maintain compatibility with the 2.7V to 5.5V load voltage range, dual-output 1:2 topology, and equivalent package footprint. Selection between these parts depends on output channel type requirements, current capacity needs, temperature operating range, and storage environment conditions.

Frequently Asked Questions (FAQ)

Q: Can the TPS2062QDGNRQ1 directly replace the AP2192MPG-13 in all applications?

A: Direct replacement is possible only when the application circuit design accommodates N-Channel output topology instead of P-Channel. The reduced maximum output current (1A vs. 1.5A) must be verified against application load requirements. Circuit-level design changes may be necessary to implement N-Channel switching logic.

Q: What is the significance of the output type difference (P-Channel vs. N-Channel)?

A: Output type determines the switching topology and gate drive requirements at the circuit level. P-Channel devices (AP2192MPG-13) pull the output to ground when activated, while N-Channel devices (TPS2062QDGNRQ1) pull the output to the supply voltage. Application schematics must be designed for the specific channel type.

Q: Are the package footprints identical between these two parts?

A: Both components use 8-pin packages with 0.118" width and 3.00mm standard dimensions with exposed pads. The AP2192MPG-13 uses 8-MSOP-EP packaging while the TPS2062QDGNRQ1 uses 8-HVSSOP packaging. Physical footprints are compatible for PCB layout purposes, though supplier device package designations differ.

Q: What are the storage and handling differences between these parts?

A: The AP2192MPG-13 carries MSL Level 1 rating, allowing unlimited shelf life storage without moisture control requirements. The TPS2062QDGNRQ1 carries MSL Level 2 rating, requiring controlled storage conditions with a maximum 1-year shelf life from the date of manufacture. Moisture sensitivity handling procedures must be followed for the TPS2062QDGNRQ1 during assembly operations.

Q: How do the fault protection features compare?

A: Both parts include current limiting (fixed), over-temperature protection, and UVLO (under-voltage lockout). The AP2192MPG-13 includes additional reverse current protection. The TPS2062QDGNRQ1 omits reverse current protection but includes automotive-grade qualification (AEC-Q100).

Q: What is the impact of the 0.5A current difference on application design?

A: The AP2192MPG-13 supports 1.5A maximum output current per channel, while the TPS2062QDGNRQ1 supports 1A maximum. Applications requiring sustained output currents above 1A per channel must use the AP2192MPG-13. For applications with maximum load currents at or below 1A, the TPS2062QDGNRQ1 is suitable.

Q: Are both parts suitable for automotive applications?

A: The TPS2062QDGNRQ1 includes AEC-Q100 automotive qualification. The AP2192MPG-13 does not carry automotive qualification designation. Selection for automotive applications requires the TPS2062QDGNRQ1 when automotive-grade certification is a design requirement.

Q: What is the operating temperature range difference?

A: The AP2192MPG-13 operates from -40°C to 85°C. The TPS2062QDGNRQ1 operates from -40°C to 125°C. Applications requiring operation above 85°C ambient temperature must use the TPS2062QDGNRQ1.