Request Quote
(Ships tomorrow)
AD8512BRZ Equivalent & Substitute Parts
Part Overview
The AD8512BRZ is a J-FET operational amplifier manufactured by Analog Devices Inc., configured as a dual-channel (2 circuit) device in an 8-SOIC surface mount package. This component is classified as a linear amplifier and maintains Active product status. The AD8512BRZ is specified for applications requiring low input bias current, low input offset voltage, and moderate slew rate performance across an extended operating temperature range of -40°C to 125°C.
Substitute parts are identified when equivalent electrical performance, mechanical compatibility, and functional characteristics align with the original specification. Substitution becomes necessary when the primary part experiences supply constraints, extended lead times, or when design requirements permit operation within the electrical parameter tolerances of alternative devices.
Substiute Parts
Key Parameters
| Parameter | Value | Unit |
|---|---|---|
| Amplifier Type | J-FET | — |
| Number of Circuits | 2 | — |
| Slew Rate | 20 | V/µs |
| Gain Bandwidth Product | 8 | MHz |
| Current - Input Bias | 25 | pA |
| Voltage - Input Offset | 80 | µV |
| Current - Supply | 2.2 (x2 Channels) | mA |
| Current - Output / Channel | 70 | mA |
| Voltage - Supply Span (Min) | 10 | V |
| Voltage - Supply Span (Max) | 30 | V |
| Operating Temperature | -40 to 125 | °C |
| Package / Case | 8-SOIC (0.154", 3.90mm Width) | — |
| Mounting Type | Surface Mount | — |
| RoHS Status | ROHS3 Compliant | — |
| Moisture Sensitivity Level | 1 (Unlimited) | — |
Substitute Part Grouping Explanation
Substitute parts for the AD8512BRZ are identified based on strict alignment with the following critical parameters:
Primary Substitution Criteria:
- Amplifier Type: J-FET configuration
- Number of Circuits: 2 (dual-channel)
- Package / Case: 8-SOIC form factor
- Mounting Type: Surface Mount
- Slew Rate: 20 V/µs (or equivalent performance tier)
- Gain Bandwidth Product: 8 MHz (or equivalent performance tier)
- Input Bias Current: 25 pA (or lower)
- Input Offset Voltage: 80 µV (or lower)
- Supply Voltage Range: Minimum 10 V to Maximum 30 V (or broader range)
- Operating Temperature: -40°C to 125°C (or equivalent extended range)
Substitutes are grouped into two categories:
Category A - Direct Electrical Equivalents: Parts matching the AD8512BRZ slew rate (20 V/µs) and gain bandwidth product (8 MHz) with J-FET input architecture and identical package configuration.
Category B - Functional Alternatives: Parts with J-FET input architecture in 8-SOIC packages that operate within the supply voltage and temperature ranges but with different performance characteristics (lower slew rate, different bandwidth, or modified input specifications).
All substitute parts maintain ROHS3 compliance, surface mount 8-SOIC packaging, and active product status.
Parameter Comparison
| Part Number | Manufacturer | Amplifier Type | Slew Rate (V/µs) | GBW (MHz) | Input Bias (pA) | Input Offset (µV) | Supply Current (mA) | Output Current (mA) | Supply Min (V) | Supply Max (V) | Temp Range (°C) | Package |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AD8512BRZ | Analog Devices | J-FET | 20 | 8 | 25 | 80 | 2.2 | 70 | 10 | 30 | -40 to 125 | 8-SOIC |
| LF253DT | STMicroelectronics | J-FET | 16 | 4 | 20 | 3000 | 1.4 | 40 | 6 | 36 | -40 to 105 | 8-SOIC |
| LF353DT | STMicroelectronics | J-FET | 16 | 4 | 20 | 3000 | 1.4 | 40 | 6 | 36 | 0 to 70 | 8-SOIC |
| LM833DT | STMicroelectronics | Audio | 7 | 15 | 300 | 300 | 4 | 37 | 5 | 30 | -40 to 105 | 8-SOIC |
| OPA2132U/2K5 | Texas Instruments | J-FET | 20 | 8 | 5 | 250 | 4 | 40 | 5 | 36 | -40 to 85 | 8-SOIC |
| OPA2132UA | Texas Instruments | J-FET | 20 | 8 | 5 | 500 | 4 | 40 | 5 | 36 | -40 to 85 | 8-SOIC |
| OPA2132UA/2K5 | Texas Instruments | J-FET | 20 | 8 | 5 | 500 | 4 | 40 | 5 | 36 | -40 to 85 | 8-SOIC |
| TL062CDT | STMicroelectronics | J-FET | 3.5 | 1 | 30 | 3000 | 0.2 | 20 | 6 | 36 | 0 to 70 | 8-SOIC |
| TL062IDT | STMicroelectronics | J-FET | 3.5 | 1 | 30 | 3000 | 0.2 | 20 | 6 | 36 | -40 to 105 | 8-SOIC |
| TL072ACDT | STMicroelectronics | J-FET | 16 | 4 | 20 | 3000 | 1.4 | 40 | 6 | 36 | 0 to 70 | 8-SOIC |
| TL072CDT | STMicroelectronics | J-FET | 16 | 4 | 20 | 3000 | 1.4 | 40 | 6 | 36 | 0 to 70 | 8-SOIC |
Engineering Selection Recommendations
Direct Electrical Equivalents (Recommended for Performance-Critical Applications):
The OPA2132U/2K5, OPA2132UA, and OPA2132UA/2K5 manufactured by Texas Instruments provide the closest electrical match to the AD8512BRZ. These devices share identical slew rate (20 V/µs) and gain bandwidth product (8 MHz) specifications. The OPA2132 series exhibits lower input bias current (5 pA versus 25 pA) and maintains J-FET input architecture. All three variants are ROHS3 compliant and operate within the 8-SOIC package standard. The primary trade-off is reduced maximum operating temperature (85°C versus 125°C for the AD8512BRZ) and higher moisture sensitivity level (MSL 3 versus MSL 1).
Functional Alternatives (For Applications Tolerant of Performance Variation):
The LF253DT, LF353DT, TL072ACDT, and TL072CDT provide J-FET input architecture in 8-SOIC packages with broader supply voltage ranges (6 V to 36 V). These alternatives operate at reduced slew rate (16 V/µs) and lower gain bandwidth product (4 MHz). Input bias current remains comparable (20 pA), but input offset voltage increases to 3 mV. These devices are suitable for applications where the AD8512BRZ performance specifications exceed design requirements.
Limited Compatibility Alternative:
The LM833DT is classified as an Audio amplifier rather than a J-FET operational amplifier. While packaged in 8-SOIC format, it exhibits significantly different electrical characteristics: higher input bias current (300 nA), higher input offset voltage (300 µV), and lower slew rate (7 V/µs). This device is not recommended as a direct substitute for the AD8512BRZ.
Temperature Range Considerations:
Applications requiring the full -40°C to 125°C operating range of the AD8512BRZ are limited to the OPA2132 series (maximum 85°C) or the TL062IDT (maximum 105°C). The LF253DT and TL062IDT support extended low-temperature operation (-40°C) but with reduced upper temperature limits.
All substitute parts maintain ROHS3 compliance and active product status consistent with the AD8512BRZ.
Frequently Asked Questions (FAQ)
Q: Can the OPA2132U/2K5 replace the AD8512BRZ in all applications?
A: The OPA2132U/2K5 provides equivalent slew rate and gain bandwidth product performance with superior input bias current specifications. However, the maximum operating temperature is limited to 85°C compared to 125°C for the AD8512BRZ. Substitution is valid only for applications operating within the 85°C maximum temperature constraint.
Q: What is the primary difference between LF253DT and LF353DT?
A: Both devices share identical electrical specifications. The primary difference is operating temperature range: LF253DT operates from -40°C to 105°C, while LF353DT operates from 0°C to 70°C. Selection depends on the minimum operating temperature requirement of the application.
Q: Why does the LM833DT have different electrical characteristics?
A: The LM833DT is classified as an Audio amplifier rather than a precision J-FET operational amplifier. It is optimized for audio frequency applications and exhibits higher input bias current (300 nA) and input offset voltage (300 µV). This device is not recommended as a substitute for the AD8512BRZ in precision analog applications.
Q: Are all substitute parts available in the same packaging format?
A: All listed substitute parts are packaged in 8-SOIC (0.154", 3.90mm Width) surface mount configuration, identical to the AD8512BRZ. Mechanical compatibility is maintained across all alternatives.
Q: What is the significance of Moisture Sensitivity Level (MSL) differences?
A: The AD8512BRZ carries MSL 1 (Unlimited), indicating no moisture sensitivity constraints during storage and handling. The OPA2132 series carries MSL 3 (168 Hours), requiring controlled humidity storage and limiting shelf life. This affects supply chain management and component handling procedures.
Q: Can the TL062 series replace the AD8512BRZ?
A: The TL062CDT and TL062IDT are low-power J-FET operational amplifiers with significantly reduced performance specifications: slew rate of 3.5 V/µs and gain bandwidth product of 1 MHz. These devices are suitable only for applications where the AD8512BRZ performance exceeds design requirements and power consumption is a primary constraint.
Q: What supply voltage range is required for substitution?
A: The AD8512BRZ requires 10 V to 30 V supply span. Most substitute parts operate across broader ranges (5 V to 36 V or 6 V to 36 V). Substitution is valid when the application supply voltage falls within both the original and substitute part specifications.
Q: Are all substitute parts ROHS3 compliant?
A: All listed substitute parts maintain ROHS3 compliance consistent with the AD8512BRZ, ensuring compatibility with environmental and regulatory requirements.
Alternative Parts
SJ6012L2TP
Littelfuse Inc.
6 Alternative Parts
JMK107BBJ476MA-RE
Taiyo Yuden
10 Alternative Parts
GMK107BBJ475MA-T
Taiyo Yuden
5 Alternative Parts
SJ6020N2ARP
Littelfuse Inc.
3 Alternative Parts
SJ6025R2ATP
Littelfuse Inc.
4 Alternative Parts
2474-05L
API Delevan Inc.
1 Alternative Parts
4590R-684K
API Delevan Inc.
1 Alternative Parts
CM6560R-334
API Delevan Inc.
1 Alternative Parts
CM6460-104
API Delevan Inc.
1 Alternative Parts
5526-12
API Delevan Inc.
1 Alternative Parts