Ohmite 95J700 Equivalent & Substitute Parts

Part Overview

The Ohmite 95J700 is a 700 Ohm, 5% tolerance, 5W axial wirewound resistor with flame retardant coating and safety features. This component is classified as Active product status and is suitable for through-hole applications requiring moderate power dissipation. Substitute parts are identified when equivalent electrical specifications and mechanical compatibility are maintained across the allowed parameter range for this resistor category.

Substiute Parts

95J700

OhmiteIn Stock: 107095J700 Datasheet

Current PartRFQ

25J700

OhmiteIn Stock: 114225J700 Datasheet

MFR RecommendedRFQ

95J700E

OhmiteIn Stock: 88695J700E Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the 95J700 are qualified based on matching the following critical parameters: resistance value (700 Ohms), tolerance (±5%), power rating (5W), composition (wirewound), package type (axial), and temperature coefficient (±30ppm/°C). Physical dimensions may vary within acceptable limits for axial through-hole mounting. All substitutes maintain the flame retardant coating and safety features required for this application category.

The 95J700 has two identified substitutes:

• 25J700: Manufacturer-recommended substitute from the Ohmite 20 series
• 95J700E: Parametric equivalent from the Ohmite 90 series

Parameter Comparison

Engineering Selection Recommendations

95J700 (Original Part): Active product status with RoHS non-compliant classification. Suitable for applications without RoHS requirements. Dimensions: 6.70mm diameter x 24.60mm length.

25J700 (Manufacturer-Recommended Substitute): Active product status with RoHS non-compliant classification. Slightly larger physical dimensions (7.00mm diameter x 25.80mm length) due to series variation. Maintains all electrical specifications. Select when space constraints are not critical and RoHS compliance is not required.

95J700E (Parametric Equivalent): Active product status with ROHS3 compliance. Identical dimensions to the original 95J700 (6.70mm diameter x 24.60mm length). Moisture Sensitivity Level rated at 1 (Unlimited). Select for applications requiring RoHS3 compliance or when moisture sensitivity specifications are relevant to the end application.

Frequently Asked Questions (FAQ)

Q: Can 25J700 be used as a direct replacement for 95J700? A: Yes. The 25J700 maintains all critical electrical parameters (700 Ohms, ±5% tolerance, 5W power rating, ±30ppm/°C temperature coefficient) and mechanical compatibility as an axial wirewound resistor. Physical dimensions are slightly larger (7.00mm x 25.80mm versus 6.70mm x 24.60mm), which may affect board layout in space-constrained designs.

Q: What is the primary difference between 95J700E and the original 95J700? A: The 95J700E is ROHS3 compliant, whereas the original 95J700 is RoHS non-compliant. Both share identical electrical specifications and physical dimensions. The 95J700E also specifies Moisture Sensitivity Level 1 (Unlimited). Select 95J700E for applications requiring RoHS3 compliance.

Q: Are all three parts interchangeable in the same circuit? A: All three parts are electrically equivalent with matching resistance, tolerance, power rating, and temperature coefficient. Mechanical interchangeability depends on board layout constraints. The 25J700 has slightly larger dimensions and should be verified for fit in space-constrained applications. The 95J700E is dimensionally identical to the original 95J700.

Q: Which substitute should I select for a new design? A: For new designs, 95J700E is recommended due to ROHS3 compliance, which aligns with current regulatory standards. It maintains identical dimensions and electrical performance to the original 95J700. The 25J700 is suitable when RoHS compliance is not a requirement and inventory availability is a priority.

Q: Do these parts require different handling or storage procedures? A: The 95J700E specifies Moisture Sensitivity Level 1 (Unlimited), indicating no moisture sensitivity restrictions. The original 95J700 and 25J700 are listed as Not Applicable for MSL, indicating standard handling procedures apply to all three parts.