Grayhill 95C06D3T Tactile Switch SPST-NO Equivalent & Substitute Parts

Part Overview

The Grayhill 95C06D3T is an active-status tactile switch with SPST-NO (Single Pole Single Throw, Normally Open) circuit configuration. This through-hole mounted component operates at 0.05A @ 12VDC with top actuation and polyamide actuator construction. The part is ROHS3 compliant and carries MSL 1 (Unlimited) moisture sensitivity rating.

Substitute parts are identified when equivalent electrical performance, mechanical compatibility, and regulatory compliance can be maintained across alternative manufacturers and series designations. The following E-Switch components provide functional equivalence under specified parameter constraints.

Substiute Parts

95C06D3T

Grayhill Inc.In Stock: 93595C06D3T Datasheet

Current PartRFQ

TL1105BF160Q

E-SwitchIn Stock: 10134TL1105BF160Q Datasheet

SimilarRFQ

TL1105BF250Q

E-SwitchIn Stock: 16087TL1105BF250Q Datasheet

SimilarRFQ

TL1105GF160Q

E-SwitchIn Stock: 1567TL1105GF160Q Datasheet

SimilarRFQ

TL1105GF250Q

E-SwitchIn Stock: 3870TL1105GF250Q Datasheet

SimilarRFQ

TL6100CF130QP

E-SwitchIn Stock: 818TL6100CF130QP Datasheet

SimilarRFQ

TL6100DF130QP

E-SwitchIn Stock: 1797TL6100DF130QP Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility is determined by strict alignment of the following critical parameters:

Mandatory Electrical Equivalence:

• Circuit configuration: SPST-NO
• Switch function: Off-Mom (Momentary)
• Contact rating: 0.05A @ 12VDC
• Termination style: PC Pin

Mandatory Mechanical Compatibility:

• Mounting type: Through Hole
• Actuator orientation: Top Actuated
• Actuator material: Polyamide (PA), Nylon

Regulatory & Compliance Alignment:

• RoHS3 Compliant
• MSL 1 (Unlimited)
• REACH Unaffected status

Allowed Parameter Variations: Substitute parts may differ in the following parameters while maintaining functional equivalence:

• Actuator height (vertical): ±0.20mm tolerance acceptable for PCB clearance design
• Outline dimensions: Minor variations (6.00mm x 6.00mm vs. 6.20mm x 6.20mm) acceptable for footprint compatibility
• Operating force: 130gf to 250gf range acceptable for application-specific actuation requirements
• Switch travel: 0.25mm to 0.50mm acceptable for tactile feedback consistency
• Mechanical life: 100,000 to 1,000,000 cycles acceptable based on duty cycle requirements
• Operating temperature range: Extended ranges (-40°C to -20°C lower bound; 70°C to 85°C upper bound) acceptable
• Packaging format: Bag, Bulk, or Tube acceptable for procurement logistics

Parameter Comparison

Engineering Selection Recommendations

Direct Electrical Equivalents (Identical Contact Rating & Circuit):

All listed substitute parts maintain the 0.05A @ 12VDC contact rating and SPST-NO circuit configuration required for direct functional replacement. All parts are ROHS3 compliant and carry MSL 1 (Unlimited) rating, confirming regulatory alignment with the 95C06D3T.

TL1105 Series Selection (E-Switch):

The TL1105BF160Q and TL1105GF160Q variants provide 160gf operating force matching the 95C06D3T specification. These parts feature 9.50mm and 9.70mm actuator heights respectively, maintaining vertical clearance compatibility. The TL1105 series operates at -20°C to 70°C, which covers the 95C06D3T operating range with a 5°C lower temperature limit reduction. Mechanical life is rated at 100,000 cycles, representing a 10:1 reduction from the 95C06D3T specification.

The TL1105BF250Q and TL1105GF250Q variants provide 250gf operating force for applications requiring increased actuation resistance. These parts are electrically and mechanically compatible with the 95C06D3T but introduce higher actuation force as a design parameter change.

TL6100 Series Selection (E-Switch):

The TL6100CF130QP and TL6100DF130QP variants provide extended operating temperature range (-40°C to 85°C) and 1,000,000 cycle mechanical life matching the 95C06D3T durability specification. These parts feature process-sealed construction and 130gf operating force. Actuator heights are 6.90mm (CF variant) and 10.00mm (DF variant), providing vertical clearance options. Outline dimensions are 7.20mm x 7.20mm, representing a 1.0mm increase in footprint compared to the 95C06D3T.

Substitution Constraints:

• TL1105 series parts are suitable for applications where 100,000 cycle mechanical life is acceptable and operating temperature does not fall below -20°C.
• TL6100 series parts are suitable for applications requiring extended temperature operation and 1,000,000 cycle durability, with acceptance of increased footprint dimensions and 0.50mm switch travel.
• Outline dimension variations (6.00mm, 6.20mm, 7.20mm) require PCB layout verification for clearance and spacing compliance.

Frequently Asked Questions (FAQ)

Q: Can TL1105 series parts directly replace the 95C06D3T in all applications?

A: TL1105 series parts provide electrical and mechanical compatibility for the 95C06D3T contact rating and circuit configuration. However, the 100,000 cycle mechanical life rating is 10 times lower than the 95C06D3T specification. Substitution is valid only when application duty cycle does not exceed 100,000 total actuations. Additionally, the -20°C lower operating temperature limit (versus -25°C for the 95C06D3T) must be evaluated for environmental compliance.

Q: What is the difference between TL1105BF and TL1105GF variants?

A: Both variants are electrically identical with 0.05A @ 12VDC contact rating and SPST-NO circuit configuration. The primary difference is actuator height: TL1105BF series provides 9.50mm height (matching 95C06D3T), while TL1105GF series provides 9.70mm height. The 0.20mm height difference requires PCB clearance verification for overlay components or enclosure constraints.

Q: Why do TL6100 series parts have larger outline dimensions?

A: TL6100 series parts (7.20mm x 7.20mm outline) incorporate process-sealed construction and extended temperature range capability (-40°C to 85°C). The increased footprint accommodates internal sealing mechanisms that provide enhanced environmental protection. This design change is independent of electrical performance and does not affect contact rating or circuit configuration.

Q: Can operating force variations (130gf, 160gf, 250gf) be used interchangeably?

A: Operating force is a design parameter that directly affects user actuation experience and mechanical stress on the switch mechanism. The 95C06D3T specifies 160gf. Substitution with 130gf (TL6100 series) or 250gf (TL1105BF250Q, TL1105GF250Q) variants requires application-level evaluation of tactile feedback requirements and mechanical stress tolerance. These are not interchangeable without design review.

Q: What packaging format differences exist among substitute parts?

A: The 95C06D3T is supplied in Bag packaging. Substitute parts are available in Bulk (TL1105 series) or Tube (TL6100 series) packaging. Packaging format does not affect component electrical or mechanical performance and is determined by procurement and inventory management requirements.

Q: Are all substitute parts ROHS3 compliant?

A: All listed substitute parts carry ROHS3 Compliant status and REACH Unaffected designation, matching the 95C06D3T regulatory profile. MSL 1 (Unlimited) moisture sensitivity rating is consistent across all parts, confirming equivalent handling and storage requirements.

Q: What is the significance of switch travel differences (0.25mm vs. 0.50mm)?

A: Switch travel defines the distance the actuator moves from rest position to full contact closure. The 95C06D3T specifies 0.25mm travel. TL6100 series parts specify 0.50mm travel, which affects tactile feedback characteristics and mechanical response time. This parameter difference requires application-level evaluation for user interface consistency.