Amphenol ICC 861400061YO2LF Equivalent & Substitute Parts

Part Overview

The Amphenol ICC 861400061YO2LF is a rectangular connector header designed for through-hole mounting applications. This 6-position, 0.100" (2.54mm) pitch connector operates across -55°C to 125°C and supports 3A current at 1000V voltage rating. The part is Active status and RoHS Compliant with UL94 V-0 flammability rating. Substitute parts are identified when equivalent electrical and mechanical parameters align with the main part specifications, enabling direct replacement in board-to-board or board-to-cable interconnect applications.

Substiute Parts

861400061YO2LF

Amphenol ICC (FCI)In Stock: 1099861400061YO2LF Datasheet

Current PartRFQ

0022284061

MolexIn Stock: 16350022284061 Datasheet

MFR RecommendedRFQ

0022284064

MolexIn Stock: 21260022284064 Datasheet

MFR RecommendedRFQ

87224-6

TE Connectivity AMP ConnectorsIn Stock: 84487224-6 Datasheet

MFR RecommendedRFQ

929647-01-06-EU

3MIn Stock: 1287929647-01-06-EU Datasheet

MFR RecommendedRFQ

929647-01-06-I

3MIn Stock: 2083929647-01-06-I Datasheet

MFR RecommendedRFQ

929647-03-06-I

3MIn Stock: 1136929647-03-06-I Datasheet

MFR RecommendedRFQ

929647-09-06-I

3MIn Stock: 1639929647-09-06-I Datasheet

MFR RecommendedRFQ

929834-01-06-RK

3MIn Stock: 2673929834-01-06-RK Datasheet

MFR RecommendedRFQ

TSW-106-24-F-S

Samtec Inc.In Stock: 1103TSW-106-24-F-S Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the 861400061YO2LF are qualified based on the following critical parameters:

Electrical Compatibility:

• Pitch - Mating: 0.100" (2.54mm)
• Number of Positions: 6
• Number of Rows: 1
• Contact Type: Male Pin
• Fastening Type: Push-Pull

Mechanical Compatibility:

• Mounting Type: Through Hole
• Termination: Solder
• Contact Shape: Square
• Connector Type: Header or Header, Breakaway

Environmental & Compliance:

• Material Flammability Rating: UL94 V-0
• Moisture Sensitivity Level: 1 (Unlimited)
• Product Status: Active

Substitutes are grouped by contact finish material and post length variations, which affect mating interface characteristics and board-level integration. All qualified substitutes maintain the core 6-position, 2.54mm pitch architecture and through-hole solder termination required for direct replacement.

Parameter Comparison

Engineering Selection Recommendations

All listed substitute parts maintain Active product status and meet UL94 V-0 flammability requirements. Selection between substitutes depends on specific application constraints:

Gold-Finish Substitutes (0022284064, 87224-6, 929647-01-06-EU, 929647-01-06-I, 929647-03-06-I, 929647-09-06-I, TSW-106-24-F-S): These parts provide gold contact finish matching the primary part's mating interface specification. Gold-finished contacts support superior corrosion resistance and signal integrity in demanding environments.

Tin-Finish Substitutes (0022284061, 929834-01-06-RK): These parts feature tin contact finish and are suitable for general-purpose applications where gold plating is not required.

Temperature Range Considerations: The main part 861400061YO2LF operates -55°C to 125°C. Substitute parts 929647 and 929834 series operate -40°C to 105°C, representing a narrower temperature envelope. TSW-106-24-F-S matches the full -55°C to 125°C range. Application thermal requirements determine suitability.

Current Rating: The main part supports 3A. Molex 0022284061 and 0022284064 do not specify current rating. 3M 929 series parts specify 2.5A. TE Connectivity 87224-6 specifies 3A. Samtec TSW-106-24-F-S does not specify current rating. Applications requiring 3A continuous current should prioritize parts with explicit 3A ratings.

RoHS Compliance: All substitutes are RoHS Compliant or ROHS3 Compliant except TE Connectivity 87224-6, which is Not applicable. Regulatory requirements determine compliance necessity.

Frequently Asked Questions (FAQ)

Q: Can I substitute the Amphenol ICC 861400061YO2LF with any of the listed parts?

A: Direct substitution is possible for all listed parts based on core electrical and mechanical parameters: 6-position, 2.54mm pitch, male pin header, through-hole solder termination, and push-pull fastening. However, differences in contact finish, insulation material, operating temperature range, and current rating may affect performance in specific applications. Verify that the substitute meets your application's electrical, thermal, and compliance requirements.

Q: What is the difference between gold and tin contact finishes?

A: Gold-finished contacts provide superior corrosion resistance, lower contact resistance, and extended shelf life, making them suitable for high-reliability applications. Tin-finished contacts are cost-effective for general-purpose applications where corrosion resistance is less critical. Both finishes support the 2.54mm pitch mating interface.

Q: Do all substitutes support the same current and voltage ratings?

A: No. The main part supports 3A at 1000V. Molex parts do not specify current or voltage ratings. 3M 929 series parts specify 2.5A with unspecified voltage. TE Connectivity 87224-6 specifies 3A with unspecified voltage. Samtec TSW-106-24-F-S does not specify current or voltage. Verify that the substitute meets your application's power requirements.

Q: Are there temperature range differences between the main part and substitutes?

A: Yes. The main part operates -55°C to 125°C. 3M 929 series and 929834 parts operate -40°C to 105°C. TE Connectivity 87224-6 operates -65°C to 105°C. Samtec TSW-106-24-F-S operates -55°C to 125°C, matching the main part. Select substitutes based on your application's thermal operating envelope.

Q: What insulation materials are used in the substitute parts?

A: The main part uses Thermoplastic insulation. Molex parts use Polyamide (PA), Nylon, Glass Filled. 3M 929647 series uses Polybutylene Terephthalate (PBT), Polyester, Glass Filled or Polycyclohexylenedimethylene Terephthalate (PCT). TE Connectivity 87224-6 uses Thermoplastic. Samtec TSW-106-24-F-S uses Polybutylene Terephthalate (PBT). Insulation material affects mechanical durability and thermal performance.

Q: Are all substitutes RoHS compliant?

A: Most substitutes are RoHS Compliant or ROHS3 Compliant. TE Connectivity 87224-6 is marked Not applicable for RoHS status. Verify RoHS compliance requirements for your application and regulatory jurisdiction.

Q: What is the difference between the 3M 929647 variants (01-06-EU, 01-06-I, 03-06-I, 09-06-I)?

A: These variants differ in contact post length: 929647-01-06-EU and 929647-01-06-I have 0.110" (2.79mm) post length; 929647-03-06-I has 0.410" (10.41mm) post length; 929647-09-06-I has 0.145" (3.68mm) post length. Post length affects board-level integration depth and mating interface geometry. Select the variant matching your PCB thickness and connector cavity depth requirements.

Q: Can I use Molex 0022284061 and 0022284064 interchangeably?

A: Both are 6-position, 2.54mm pitch Molex KK254 headers with identical mechanical dimensions. The primary difference is contact finish: 0022284061 uses Tin finish; 0022284064 uses Gold finish. They are mechanically interchangeable but electrically differentiated by finish material. Select based on your application's corrosion resistance and signal integrity requirements.