Equivalent & Substitute Parts for 8-2176093-9

Part Overview

The TE Connectivity 8-2176093-9 is an 86.6 kOhms ±0.1% thin film chip resistor in 0805 (2012 Metric) package rated for 0.25W (1/4W) power dissipation. This component is part of the RP73P series from Holsworthy and maintains active product status with full RoHS3 compliance and unlimited moisture sensitivity rating (MSL 1). Substitute parts are identified when equivalent electrical specifications and mechanical compatibility are required for design flexibility, supply chain alternatives, or specific application requirements.

Substiute Parts

8-2176093-9

TE Connectivity Passive ProductIn Stock: 18378-2176093-9 Datasheet

Current PartRFQ

ERA-6AEB8662V

Panasonic Electronic ComponentsIn Stock: 20240ERA-6AEB8662V Datasheet

DirectRFQ

RG2012P-8662-B-T5

SusumuIn Stock: 15045RG2012P-8662-B-T5 Datasheet

DirectRFQ

RT0805BRD0786K6L

YAGEOIn Stock: 6121RT0805BRD0786K6L Datasheet

DirectRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the 8-2176093-9 is determined by the following critical parameters:

Electrical Equivalence Requirements:

• Resistance value: 86.6 kOhms (exact match required)
• Tolerance: ±0.1% (exact match required)
• Temperature coefficient: ±25ppm/°C (exact match required)
• Operating temperature range: -55°C ~ 155°C (minimum requirement)

Mechanical Compatibility Requirements:

• Package / Case: 0805 (2012 Metric) (exact match required)
• Composition: Thin Film (exact match required)
• Number of terminations: 2 (exact match required)

Compliance Requirements:

• RoHS3 Compliant (mandatory)
• Moisture Sensitivity Level: 1 (Unlimited) (mandatory)

Power Rating Consideration: Substitute parts rated at 0.125W (1/8W) are functionally equivalent to the 0.25W (1/4W) main part when the application circuit design does not require the higher power dissipation capability. The 0.125W rating represents a conservative thermal design margin and does not affect electrical performance in circuits designed for the 0.25W specification.

Parameter Comparison

Engineering Selection Recommendations

All four parts listed maintain active product status and full RoHS3 compliance with unlimited moisture sensitivity rating, ensuring long-term availability and environmental regulatory adherence.

ERA-6AEB8662V (Panasonic): This substitute incorporates AEC-Q200 automotive qualification, providing enhanced reliability documentation for applications requiring automotive-grade component certification. The 0.125W power rating is suitable for circuits where thermal dissipation does not exceed this specification.

RG2012P-8662-B-T5 (Susumu): This substitute combines AEC-Q200 automotive qualification with anti-sulfur coating technology, offering additional environmental protection in corrosive atmospheres. The lowest seated height (0.020" / 0.50mm) provides design flexibility for space-constrained PCB layouts. The 0.125W power rating applies the same thermal design consideration as the Panasonic alternative.

RT0805BRD0786K6L (YAGEO): This substitute provides a standard thin film 0805 resistor without automotive qualification, suitable for general industrial and commercial applications. The 0.125W power rating follows the same thermal design principle as other substitutes.

Selection between these substitutes depends on application-specific requirements: automotive qualification needs, environmental protection specifications, or PCB height constraints. All substitutes maintain electrical equivalence to the main part across resistance, tolerance, temperature coefficient, and operating temperature specifications.

Frequently Asked Questions (FAQ)

Q: Can ERA-6AEB8662V, RG2012P-8662-B-T5, or RT0805BRD0786K6L be used as direct replacements for 8-2176093-9?

A: Yes. All three substitute parts match the critical electrical parameters (86.6 kOhms ±0.1%, ±25ppm/°C temperature coefficient) and mechanical specifications (0805 package, thin film composition, 2-termination configuration). All maintain RoHS3 compliance and MSL 1 rating. The 0.125W power rating of the substitutes is functionally equivalent in applications where circuit power dissipation does not exceed this specification.

Q: What is the difference between the 0.25W main part and the 0.125W substitute parts?

A: The power rating indicates maximum continuous power dissipation capability. The 0.25W (1/4W) main part accommodates higher thermal loads than the 0.125W (1/8W) substitutes. In circuit designs where actual power dissipation remains below 0.125W, the substitute parts perform identically. Applications requiring sustained power dissipation above 0.125W should retain the 0.25W main part.

Q: Are there package or footprint differences between these parts?

A: All parts use the 0805 (2012 Metric) package with identical length and width dimensions (0.079" L x 0.049" W / 2.00mm x 1.25mm). Seated heights vary slightly: 8-2176093-9 (0.026" / 0.65mm), ERA-6AEB8662V (0.024" / 0.60mm), RG2012P-8662-B-T5 (0.020" / 0.50mm), and RT0805BRD0786K6L (0.024" / 0.60mm). These height variations are within standard PCB assembly tolerances and do not affect footprint compatibility.

Q: Which substitute part is recommended for automotive applications?

A: Both ERA-6AEB8662V and RG2012P-8662-B-T5 carry AEC-Q200 automotive qualification. RG2012P-8662-B-T5 additionally includes anti-sulfur coating for enhanced environmental protection. The main part 8-2176093-9 does not carry automotive qualification; automotive applications should select either Panasonic or Susumu substitute parts.

Q: Do all parts meet the same compliance standards?

A: Yes. All four parts are ROHS3 compliant, REACH unaffected, and classified under ECCN EAR99 with HTSUS code 8533.21.0030. All maintain MSL 1 (Unlimited) moisture sensitivity rating, indicating no special moisture protection requirements during storage or handling.

Q: Can these parts be mixed in the same production batch?

A: Yes. All parts share identical electrical specifications (86.6 kOhms ±0.1%, ±25ppm/°C, -55°C ~ 155°C operating range) and mechanical compatibility (0805 package, thin film composition). Mixing is permissible from an electrical and mechanical standpoint. Supply chain or quality documentation requirements may impose additional constraints depending on application specifications.