TE Connectivity 8-2176089-2 Equivalent & Substitute Parts

Part Overview

The TE Connectivity 8-2176089-2 is a 82.5 kOhms ±0.1% thin film chip resistor in 0603 (1608 Metric) package rated for 0.167W (1/6W) power dissipation. This component is part of the RP73P series from Holsworthy and is currently in active production status. Substitute parts are identified to provide alternative sourcing options when the primary part is unavailable or when specific application requirements necessitate alternative specifications within compatible electrical and mechanical parameters.

Substiute Parts

8-2176089-2

TE Connectivity Passive ProductIn Stock: 17828-2176089-2 Datasheet

Current PartRFQ

RG1608P-8252-B-T5

SusumuIn Stock: 6126RG1608P-8252-B-T5 Datasheet

DirectRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the TE Connectivity 8-2176089-2 is determined by strict equivalence across the following critical parameters:

Electrical Equivalence Requirements:

• Resistance value: 82.5 kOhms (exact match)
• Tolerance: ±0.1% (exact match)
• Temperature coefficient: ±25ppm/°C (exact match)
• Operating temperature range: -55°C ~ 155°C (exact match or better)

Mechanical Equivalence Requirements:

• Package type: 0603 (1608 Metric) (exact match)
• Composition: Thin Film (exact match)
• Number of terminations: 2 (exact match)
• Moisture sensitivity level: 1 (Unlimited) (exact match or better)

Power Rating Consideration: Substitute parts with equal or greater power rating are functionally compatible. The primary part is rated at 0.167W (1/6W). Substitute parts rated at 0.1W (1/10W) or higher meet this requirement.

The identified substitute part RG1608P-8252-B-T5 from Susumu meets all electrical and mechanical equivalence criteria and is therefore a direct substitute.

Parameter Comparison

Engineering Selection Recommendations

Primary Part Selection: The TE Connectivity 8-2176089-2 remains the primary specification when available. This part is active in production and meets all stated application requirements.

Substitute Part Selection: The Susumu RG1608P-8252-B-T5 is a direct electrical and mechanical equivalent. Selection of this substitute is appropriate when:

• TE Connectivity 8-2176089-2 is unavailable from inventory or supply chain
• Application requirements do not mandate RoHS compliance status of the primary part
• The lower power rating (0.1W versus 0.167W) is acceptable for the circuit design
• Automotive AEC-Q200 qualification is beneficial or required for the application

Compliance Considerations: The primary part carries RoHS non-compliant status with vendor-undefined REACH status. The substitute part is ROHS3 compliant and REACH unaffected, providing improved regulatory compliance for new designs or applications with compliance requirements.

Physical Compatibility: Both parts are mechanically compatible in 0603 (1608 Metric) footprints. Minor dimensional variations (0.061" versus 0.063" length and 0.022" versus 0.020" height) are within standard PCB design tolerances and do not affect placement or soldering processes.

Frequently Asked Questions (FAQ)

Q: Can the Susumu RG1608P-8252-B-T5 be used as a direct replacement for the TE Connectivity 8-2176089-2?

A: Yes. Both parts share identical electrical specifications (82.5 kOhms, ±0.1% tolerance, ±25ppm/°C temperature coefficient, -55°C to 155°C operating range) and are packaged in the same 0603 (1608 Metric) form factor with identical termination configuration. The substitute part is electrically and mechanically compatible.

Q: What is the difference in power rating between these parts?

A: The TE Connectivity part is rated at 0.167W (1/6W), while the Susumu substitute is rated at 0.1W (1/10W). The substitute part has a lower power dissipation rating. Verify that circuit operating conditions do not exceed 0.1W continuous power dissipation when using the substitute part.

Q: Are there physical size differences between these parts?

A: Minor dimensional differences exist. The TE Connectivity part measures 0.061" L x 0.031" W (1.55mm x 0.80mm) with 0.022" maximum seated height. The Susumu part measures 0.063" L x 0.031" W (1.60mm x 0.80mm) with 0.020" maximum seated height. These variations are within standard PCB design tolerances and do not affect placement or soldering.

Q: What is the significance of the AEC-Q200 qualification on the Susumu part?

A: AEC-Q200 is an automotive industry qualification standard. The Susumu RG1608P-8252-B-T5 carries this certification, indicating suitability for automotive applications. This qualification is not present on the TE Connectivity part. Select the Susumu substitute when automotive-grade components are required.

Q: Does the Susumu part have anti-sulfur protection?

A: Yes. The Susumu RG1608P-8252-B-T5 includes anti-sulfur protection as a feature. This provides enhanced resistance to sulfur-containing environments. The TE Connectivity part does not specify this feature.

Q: What is the difference in RoHS compliance status?

A: The TE Connectivity 8-2176089-2 is RoHS non-compliant. The Susumu RG1608P-8252-B-T5 is ROHS3 compliant. For applications or regions requiring RoHS compliance, the Susumi substitute is the appropriate selection.

Q: Are both parts available in Tape & Reel packaging?

A: Yes. Both the TE Connectivity 8-2176089-2 and Susumu RG1608P-8252-B-T5 are supplied in Tape & Reel (TR) packaging, suitable for automated assembly processes.

Q: What is the moisture sensitivity level for these parts?

A: Both parts carry Moisture Sensitivity Level (MSL) 1, indicating unlimited shelf life without moisture control requirements. No special storage or handling precautions are necessary for either part.