C&K 7201P4CWZGE2 Toggle Switch DPDT Equivalent & Substitute Parts

Part Overview

The C&K 7201P4CWZGE2 is a panel-mount toggle switch with DPDT (Double Pole Double Throw) circuit configuration, rated for 5A at 120V AC and 28V DC. This switch is classified as Active product status and is RoHS3 compliant. Substitute parts are identified when equivalent electrical ratings, mechanical mounting specifications, and circuit configurations are available from alternative manufacturers, enabling procurement flexibility and supply chain continuity.

Substiute Parts

7201P4CWZGE2

C&KIn Stock: 8557201P4CWZGE2 Datasheet

Current PartRFQ

100DP1T1B1M1REH

E-SwitchIn Stock: 1774100DP1T1B1M1REH Datasheet

SimilarRFQ

100DP1T6B11M1QEH

E-SwitchIn Stock: 1515100DP1T6B11M1QEH Datasheet

SimilarRFQ

100DP1T6B11M1REH

E-SwitchIn Stock: 1090100DP1T6B11M1REH Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the 7201P4CWZGE2 are grouped based on strict electrical and mechanical compatibility criteria. The primary substitution logic is determined by the following parameters:

Critical Matching Parameters:

• Circuit configuration (DPDT required)
• Switch function (On-On required)
• Current rating (5A AC/DC for full compatibility)
• Voltage rating (120V AC / 28V DC for full compatibility)
• Mounting type (Panel Mount required)
• Panel cutout dimensions (Circular 6.35mm Dia required)
• Bushing thread (1/4-40 required)
• Termination style (Solder Lug required)
• Operating temperature range (-30°C to 85°C minimum)

Substitute Categories:

Category 1: Full Electrical & Mechanical Equivalents Parts matching all critical parameters including 5A/120V AC rating.

Category 2: Reduced Electrical Rating Substitutes Parts with identical mechanical and circuit specifications but lower current/voltage ratings (0.4VA/20V). These are suitable only for applications with reduced power requirements.

Parameter Comparison

Engineering Selection Recommendations

100DP1T6B11M1QEH (E-Switch) - Primary Substitute

This part provides full electrical equivalence to the 7201P4CWZGE2, matching the 5A/120V AC and 28V DC ratings with identical DPDT On-On circuit configuration and panel-mount specifications. Both parts are RoHS3 compliant and Active product status. The primary difference is actuator length (12.30mm versus 6.35mm), which may require panel design verification. Electrical life rating is lower (40,000 cycles versus 100,000 cycles). This substitute is suitable for applications requiring equivalent electrical performance.

100DP1T6B11M1REH and 100DP1T1B1M1REH (E-Switch) - Reduced Rating Substitutes

These parts maintain mechanical and circuit compatibility but operate at reduced electrical ratings (0.4VA/20V). Both are RoHS3 compliant and Active product status. These substitutes are applicable only to applications with power requirements not exceeding 0.4VA at 20V maximum. Actuator type differs on the 100DP1T1B1M1REH (Standard Round versus Flat Anti-Rotation).

Compliance Considerations

All substitute parts maintain RoHS3 compliance and Active product status, ensuring regulatory alignment with the original part. The original 7201P4CWZGE2 specifies IP67 ingress protection; substitute parts do not provide this specification and should be evaluated for environmental requirements.

Frequently Asked Questions (FAQ)

Q: Can the 100DP1T6B11M1QEH directly replace the 7201P4CWZGE2 in all applications?

A: The 100DP1T6B11M1QEH provides full electrical equivalence (5A/120V AC, 28V DC) and identical circuit configuration. However, the actuator length differs (12.30mm versus 6.35mm), requiring verification that panel cutout and actuator clearance accommodate the longer stem. Electrical life is reduced from 100,000 to 40,000 cycles. IP67 ingress protection is not specified for the substitute.

Q: What is the difference between the 100DP1T6B11M1QEH and 100DP1T6B11M1REH?

A: Both parts share identical mechanical specifications and actuator type (Flat Anti-Rotation). The 100DP1T6B11M1QEH is rated for 5A/120V AC and 28V DC, while the 100DP1T6B11M1REH is rated for 0.4VA/20V. Selection depends on application power requirements.

Q: Are the reduced-rating E-Switch parts (0.4VA/20V) suitable for my application?

A: The reduced-rating substitutes are suitable only for applications with maximum power requirements of 0.4VA at 20V. If your application requires 5A at 120V AC or 28V DC, these parts are not compatible. Verify actual circuit power consumption before selection.

Q: What is the impact of the longer actuator length on the 100DP1T6B11M1QEH?

A: The 100DP1T6B11M1QEH actuator length is 12.30mm compared to 6.35mm on the original part. This difference may affect panel aesthetics and operator feel. Verify that panel cutout depth and surrounding components accommodate the extended actuator length.

Q: Do all substitute parts meet the same environmental specifications as the 7201P4CWZGE2?

A: All substitute parts match the operating temperature range (-30°C to 85°C). However, the original 7201P4CWZGE2 specifies IP67 ingress protection (dust tight, waterproof), which is not specified for E-Switch substitutes. For applications requiring IP67 protection, environmental sealing must be independently verified.

Q: Are all parts RoHS3 compliant?

A: Yes, the 7201P4CWZGE2 and all listed substitute parts are RoHS3 compliant, ensuring regulatory alignment for applications subject to RoHS requirements.