7201L2PHCGE Toggle Switch DPDT Equivalent & Substitute Parts

Part Overview

The C&K 7201L2PHCGE is an active-status toggle switch with DPDT (Double Pole Double Throw) configuration rated for 5A at 120V AC and 28V DC. This panel-mount switch features anti-rotation actuator design, epoxy sealed terminals, and PC pin termination. Finding equivalent or substitute parts may be necessary due to inventory constraints, lead time requirements, or application-specific mechanical or electrical parameter needs.

Substiute Parts

7201L2PHCGE

C&KIn Stock: 11557201L2PHCGE Datasheet

Current PartRFQ

100DP1T1B1M2QEH

E-SwitchIn Stock: 8034100DP1T1B1M2QEH Datasheet

SimilarRFQ

100DP1T6B15M2RE

E-SwitchIn Stock: 891100DP1T6B15M2RE Datasheet

SimilarRFQ

2-1825138-4

TE Connectivity ALCOSWITCH SwitchesIn Stock: 18262-1825138-4 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the 7201L2PHCGE is determined by strict alignment of the following critical parameters:

Mandatory Matching Parameters:

• Circuit Configuration: DPDT
• Switch Function: On-On
• Mounting Type: Panel Mount
• Termination Style: PC Pin
• Panel Cutout Dimensions: Circular - 6.35mm Dia
• Bushing Thread: 1/4-40
• Operating Temperature Range: -30°C to 85°C

Electrical Compatibility Parameters:

• Current Rating: Must meet or exceed 5A (AC/DC)
• Voltage Rating - AC: Must meet or exceed 120V
• Voltage Rating - DC: Must meet or exceed 28V

Mechanical Compatibility Parameters:

• Actuator Type: Anti-Rotation preferred; Standard Round acceptable with mechanical verification
• Actuator Length: Variation acceptable within panel depth constraints

The substitute parts listed below are grouped based on their electrical rating alignment with the main part specification.

Parameter Comparison

Engineering Selection Recommendations

Full Electrical Rating Match: The E-Switch 100DP1T1B1M2QEH provides complete electrical compatibility with the 7201L2PHCGE, matching the 5A current rating and 120V AC / 28V DC voltage specifications. Both parts are ROHS3 compliant and active-status products. The primary difference is actuator type (Standard Round versus Anti-Rotation) and reduced electrical life (40,000 cycles versus 100,000 cycles). This substitute is suitable for applications where the higher cycle rating of the original part is not a design requirement.

Reduced Electrical Rating Substitutes: The E-Switch 100DP1T6B15M2RE and TE Connectivity 2-1825138-4 both operate at reduced electrical ratings (0.4VA at 20V AC/DC). These parts are suitable only for applications with electrical requirements not exceeding their specified ratings. Both maintain DPDT On-On configuration, panel mount design, and identical mechanical interface parameters. The TE Connectivity part exhibits significantly lower electrical life (6,000 cycles) compared to the main part and E-Switch alternatives.

Compliance Considerations: All listed parts maintain ROHS3 compliance. The E-Switch substitutes are REACH Unaffected, while the main part and TE Connectivity substitute are REACH Affected. Selection should account for regulatory requirements applicable to the end application.

Frequently Asked Questions (FAQ)

Q: Can the E-Switch 100DP1T1B1M2QEH directly replace the C&K 7201L2PHCGE? A: Yes, from an electrical and mechanical interface perspective. Both parts share identical voltage and current ratings (5A, 120V AC, 28V DC), DPDT On-On configuration, panel cutout dimensions, and bushing thread specifications. The actuator type differs (Standard Round versus Anti-Rotation), which may affect panel mounting feel and rotation resistance. Electrical life is lower (40,000 versus 100,000 cycles).

Q: Why are the E-Switch 100DP1T6B15M2RE and TE Connectivity 2-1825138-4 listed as substitutes if they have lower electrical ratings? A: These parts are listed because they share the same mechanical interface (panel cutout, bushing thread, termination style) and circuit configuration (DPDT On-On). They are suitable substitutes only for applications where the electrical load does not exceed 0.4VA at 20V AC/DC. Applications requiring the full 5A at 120V rating cannot use these parts.

Q: What is the impact of different actuator types on substitution? A: The main part features an Anti-Rotation actuator (13.97mm length), while some substitutes use Standard Round actuators (10.41mm length). Both types fit the same 6.35mm circular panel cutout and 1/4-40 bushing thread. The actuator type affects rotational resistance and user feel but does not impact electrical function. Shorter actuators may require verification of panel depth clearance.

Q: Are all listed parts currently in active production? A: Yes. The main part (7201L2PHCGE) and all substitute parts listed are marked as Active product status, indicating current manufacturing and availability.

Q: How do REACH and RoHS compliance differences affect part selection? A: All parts are ROHS3 compliant. The main part and TE Connectivity substitute are REACH Affected, while E-Switch substitutes are REACH Unaffected. Selection should align with regulatory requirements for the end-use region and application. REACH Affected status indicates the part contains substances of concern and may require additional documentation for certain markets.