C&K 7101SCWCGE Toggle Switch SPDT 5A 120V Equivalent & Substitute Parts

Part Overview

The C&K 7101SCWCGE is an active SPDT toggle switch rated for 5A at 120V AC with panel mount configuration. This component is designed for applications requiring reliable on-on switching with IP67 ingress protection and epoxy sealed terminals. Substitute parts become necessary when the primary manufacturer has extended lead times, inventory constraints, or when design flexibility permits equivalent alternatives that meet the same electrical and mechanical specifications.

Substiute Parts

7101SCWCGE

C&KIn Stock: 12117101SCWCGE Datasheet

Current PartRFQ

100SP1T1B1M2QEH

E-SwitchIn Stock: 4098100SP1T1B1M2QEH Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the 7101SCWCGE is determined by strict equivalence across the following critical parameters:

• Circuit configuration must be SPDT
• Current rating must be 5A AC/DC minimum
• Voltage ratings must meet or exceed 120V AC and 28V DC
• Panel mount configuration with circular 6.35mm cutout and 1/4-40 bushing thread
• PC pin termination style
• Operating temperature range of -30°C to 85°C or broader
• RoHS3 compliance status

The E-Switch 100SP1T1B1M2QEH meets all mandatory electrical and mechanical parameters for direct substitution. Both parts share identical circuit topology, current and voltage ratings, panel cutout dimensions, bushing specifications, termination style, temperature range, and RoHS compliance.

Parameter Comparison

Engineering Selection Recommendations

Both the C&K 7101SCWCGE and E-Switch 100SP1T1B1M2QEH are active products with ROHS3 compliance and EAR99 export classification. Selection between these parts should be based on availability, lead time, and inventory status rather than electrical or mechanical performance differences, as both components satisfy identical functional requirements.

The C&K 7101SCWCGE offers 100,000 electrical life cycles, while the E-Switch 100SP1T1B1M2QEH provides 40,000 cycles. For applications requiring extended operational life or higher cycle counts, the C&K part is the preferred choice. The E-Switch part carries REACH Unaffected status compared to the C&K REACH Affected designation, which may influence supply chain considerations in certain regulatory jurisdictions.

Frequently Asked Questions (FAQ)

Q: Can the E-Switch 100SP1T1B1M2QEH directly replace the C&K 7101SCWCGE in existing designs?

A: Yes. Both parts share identical electrical ratings (5A, 120V AC, 28V DC), circuit configuration (SPDT), panel mount specifications (6.35mm circular cutout, 1/4-40 bushing), termination style (PC pin), and operating temperature range (-30°C to 85°C). No design modifications are required for mechanical or electrical integration.

Q: What is the difference in electrical life between these parts?

A: The C&K 7101SCWCGE is rated for 100,000 electrical cycles, while the E-Switch 100SP1T1B1M2QEH is rated for 40,000 cycles. Applications with high switching frequency should prioritize the C&K part to ensure adequate operational life.

Q: Are there any compliance differences between these parts?

A: Both parts are ROHS3 compliant and carry EAR99 export classification. The C&K part is REACH Affected, while the E-Switch part is REACH Unaffected. This distinction may impact procurement in regions with strict REACH compliance requirements.

Q: Do both parts support the same panel cutout and bushing specifications?

A: Yes. Both parts require a circular 6.35mm diameter panel cutout with 1/4-40 bushing thread. No panel modifications are necessary when substituting between these components.

Q: What is the actuator length difference, and does it affect compatibility?

A: The C&K 7101SCWCGE has an actuator length of 10.67mm, while the E-Switch 100SP1T1B1M2QEH measures 10.41mm. This 0.26mm difference does not affect functional compatibility or panel mount integration.