Keystone Electronics 7052 LED Holder T1 3MM - Equivalent & Substitute Parts

Part Overview

The Keystone Electronics 7052 is a T1 LED standoff holder manufactured from natural nylon with a 0.500" (12.70mm) length. This component is designed to provide mechanical support and positioning for T1 3mm LED packages in electronic assemblies. The part is classified as obsolete, making identification of equivalent and substitute components essential for ongoing production support and design updates. Substitute parts must maintain compatibility with T1 LED form factors while meeting the same mechanical and material specifications.

Substiute Parts

7052

Keystone ElectronicsIn Stock: 9297052 Datasheet

Current PartRFQ

7373

CEC IndustriesIn Stock: 9747373 Datasheet

MFR RecommendedRFQ

7051

Keystone ElectronicsIn Stock: 11697051 Datasheet

Parametric EquivalentRFQ

7372

Keystone ElectronicsIn Stock: 80717372 Datasheet

Parametric EquivalentRFQ

LEDS1E-8-01

Essentra ComponentsIn Stock: 3975LEDS1E-8-01 Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the Keystone Electronics 7052 are identified based on the following critical parameters:

• LED Type: T1 form factor compatibility
• Length: 0.500" (12.70mm) dimension
• Material: Natural nylon construction
• Color: Natural finish
• RoHS Compliance: ROHS3 or equivalent compliance status
• Moisture Sensitivity Level: MSL 1 or Not Applicable

The substitute parts listed below meet these criteria and are suitable for direct replacement in applications requiring T1 LED standoff holders with identical mechanical and environmental specifications.

Parameter Comparison

Engineering Selection Recommendations

Primary Substitute - LEDS1E-8-01 (Essentra Components)

The LEDS1E-8-01 is the most direct equivalent to the Keystone Electronics 7052. It maintains identical specifications for LED type (T1), length (0.500" / 12.70mm), material (nylon), and color (natural). The part is currently in active production status with substantial inventory availability (3907 units). RoHS compliance is confirmed, and REACH status is unaffected. This part is recommended for new designs and ongoing production support.

Secondary Substitute - Keystone Electronics 7372

The 7372 is a Keystone Electronics product with active production status and the highest inventory level (8044 units). It maintains T1 LED type, natural nylon material, and natural color. The length specification is 0.480" (12.19mm), representing a 0.020" (0.51mm) dimensional variance from the original 7052. This part is suitable for applications where minor length tolerance adjustments are acceptable. ROHS3 compliance and REACH unaffected status are confirmed.

Tertiary Substitute - Keystone Electronics 7051

The 7051 is a Keystone Electronics parametric equivalent with T1 LED type and natural nylon material. Length is specified as 0.480" (12.18mm), a 0.020" (0.52mm) reduction from the original part. Product status is obsolete, similar to the 7052. This part may be considered for legacy system maintenance where inventory is available (1062 units), but active production parts are preferred for new applications.

Not Recommended - CEC Industries 7373

The CEC Industries 7373 is listed as manufacturer recommended but represents a different product category. It is specified as a lamp (14V T-1.75 / Base: G3.17 Bi-Pin) rather than an LED standoff holder. The T-1.75 form factor and bi-pin base configuration differ from the T1 standoff design of the 7052. This part is not suitable for direct substitution.

Frequently Asked Questions (FAQ)

Q: Can the LEDS1E-8-01 be used as a direct replacement for the Keystone Electronics 7052?

A: Yes. The LEDS1E-8-01 matches all critical parameters: T1 LED type, 0.500" (12.70mm) length, natural nylon material, and natural color. RoHS and REACH compliance are confirmed. The part is in active production with adequate inventory.

Q: What is the impact of using the 7372 with its 0.480" length instead of the original 0.500" length?

A: The 7372 has a 0.020" (0.51mm) shorter length. This dimensional difference must be evaluated against specific application requirements, including PCB layout, LED positioning, and mechanical clearance constraints. Use only if the reduced height is compatible with your assembly design.

Q: Why is the CEC Industries 7373 listed as a substitute if it is not compatible?

A: The 7373 is listed in the original part's substitute field but represents a different product category (lamp vs. standoff holder). It is not suitable for direct replacement in applications requiring T1 LED standoff functionality.

Q: Are all substitute parts RoHS compliant?

A: Yes. All substitute parts listed meet RoHS compliance requirements (ROHS3 Compliant or RoHS Compliant). REACH status is unaffected for all parts.

Q: Which substitute part has the best inventory availability?

A: The Keystone Electronics 7372 has the highest inventory level at 8044 units in stock. The LEDS1E-8-01 (Essentra Components) has 3907 units available and is recommended as the primary substitute due to exact dimensional matching.

Q: Can the 7051 be used for new production designs?

A: The 7051 is classified as obsolete, similar to the original 7052. While inventory is available (1062 units), it is not recommended for new production designs. Use active production parts such as the 7372 or LEDS1E-8-01 for ongoing and future applications.