Qualtek 701-30/63 IEC 320-C14 Power Entry Connector Receptacle

Part Overview

The Qualtek 701-30/63 is an AC power entry connector receptacle featuring IEC 320-C14 configuration with male blades, designed for panel mount snap-in installation. This component serves as the mating interface for power inlet applications requiring 10A at 250VAC in commercial unfiltered configurations. The part maintains active product status with full compliance to RoHS3, REACH, and international approval standards (CSA, UL, VDE). Equivalent substitute parts are identified based on matching electrical ratings, mechanical mounting specifications, and connector geometry to ensure direct functional interchangeability.

Substiute Parts

701-30/63

QualtekIn Stock: 950701-30/63 Datasheet

Current PartRFQ

701W-30/34

Qualtek Electronics Corp.In Stock: 9284701W-30/34 Datasheet

MFR RecommendedRFQ

6100.4330

SCHURTER Inc.In Stock: 74026100.4330 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the 701-30/63 are qualified based on the following critical parameters that determine functional interchangeability:

• Electrical Compatibility: Current rating (10A) and voltage rating (250VAC) must match exactly
• Connector Configuration: IEC 320-C14 style with receptacle, male blades configuration
• Mechanical Mounting: Panel mount, snap-in installation method with compatible panel thickness (0.118" / 3.00mm)
• Termination Standard: Quick Connect 0.250" (6.3mm) terminal configuration
• Position Count: 3-position connector
• Regulatory Compliance: RoHS3 compliance and international approval standards

The identified substitutes (701W-30/34 and 6100.4330) satisfy all critical electrical and mechanical parameters within the allowable tolerances for panel cutout dimensions and maintain equivalent functional performance in IEC 320-C14 power entry applications.

Parameter Comparison

Engineering Selection Recommendations

All three parts maintain active product status with full RoHS3 compliance and international regulatory approval. The 701-30/63 and 701W-30/34 share identical approval agencies (CSA, UL, VDE) and are both manufactured by Qualtek, differing only in series designation and minor panel cutout tolerances. The 6100.4330 from SCHURTER provides an alternative with different approval certifications (CCC, cULus, ENEC) and includes IP30 ingress protection rating, suitable for applications requiring enhanced environmental sealing. Panel cutout dimensions across all three parts fall within compatible tolerance ranges for standard IEC 320-C14 panel mount installations. Selection between these parts depends on specific approval requirements for the target application region and any ingress protection specifications.

Frequently Asked Questions (FAQ)

Q: Can the 701W-30/34 directly replace the 701-30/63 in existing designs?

A: Yes. Both parts share identical electrical ratings (10A, 250VAC), connector configuration (IEC 320-C14 receptacle with male blades), mounting method (panel mount snap-in), and termination standard (0.250" quick connect). Panel cutout dimensions differ by less than 0.3mm, which falls within standard manufacturing tolerances for panel mount applications.

Q: What is the primary difference between the Qualtek 701W-30/34 and SCHURTER 6100.4330?

A: The primary differences are manufacturer identity, approval agency certifications, and ingress protection rating. The SCHURTER 6100.4330 includes IP30 ingress protection, while the Qualtek parts do not specify ingress protection. Approval agencies differ: Qualtek parts carry CSA, UL, VDE certifications; SCHURTER carries CCC, cULus, ENEC certifications. All three maintain identical electrical and mechanical specifications.

Q: Are panel cutout dimension variations significant for substitution?

A: Panel cutout dimensions vary slightly across the three parts (27.20-27.50mm width, 19.70-20.00mm height). These variations are within acceptable tolerances for standard IEC 320-C14 panel mount receptacles and do not prevent direct mechanical substitution in applications with standard panel preparation.

Q: Do all substitute parts meet the same compliance standards?

A: All three parts are RoHS3 compliant and REACH unaffected. However, approval agencies differ. The 701-30/63 and 701W-30/34 carry CSA, UL, VDE approvals, while the 6100.4330 carries CCC, cULus, ENEC approvals. Selection should align with regional regulatory requirements for the target application.

Q: What packaging options are available for these parts?

A: The 701-30/63 is available in standard packaging (not specified). The 701W-30/34 and 6100.4330 are supplied in bulk packaging, suitable for high-volume production environments.