Amphenol ICC 69190-107 Equivalent & Substitute Parts

Part Overview

The Amphenol ICC 69190-107 is a rectangular connector header from the BERGSTIK® II series, designed for through-hole board-to-board applications. This 7-position, single-row connector features 0.100" (2.54mm) pitch male pins with press-fit and solder termination options. The part is classified as obsolete, making identification of functionally equivalent alternatives essential for ongoing system support and new design implementations.

Substiute Parts

69190-107

Amphenol ICC (FCI)In Stock: 99969190-107 Datasheet

Current PartRFQ

TS-107-T-AA

Samtec Inc.In Stock: 1344TS-107-T-AA Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the 69190-107 is determined by strict alignment of the following electrical and mechanical parameters:

• Connector Type & Contact Configuration: Header with male pins
• Position Count & Pitch: 7 positions at 0.100" (2.54mm) spacing
• Row Configuration: Single row layout
• Mounting Method: Through-hole PCB mounting
• Termination Compatibility: Solder-compatible termination
• Physical Form Factor: Square contact geometry with black insulation
• Environmental Classification: MSL 1 rating for moisture sensitivity

The Samtec TS-107-T-AA meets these core substitution criteria as an active-status alternative. While contact finish differs (tin versus gold), both finishes provide adequate electrical conductivity for standard signal and power applications within the specified pitch and position parameters.

Parameter Comparison

Engineering Selection Recommendations

The Samtec TS-107-T-AA is the manufacturer-recommended substitute for the obsolete Amphenol ICC 69190-107. Selection of this alternative is supported by:

• Product Status Alignment: The TS-107-T-AA maintains active production status, ensuring long-term availability and supply chain continuity.
• Mechanical Compatibility: Identical pitch (0.100"), position count (7), row configuration (1), and through-hole mounting enable direct PCB footprint compatibility.
• Electrical Equivalence: Both connectors support solder termination with equivalent MSL 1 moisture sensitivity ratings.
• Compliance Improvement: The TS-107-T-AA achieves ROHS3 compliance, addressing regulatory requirements that the non-compliant 69190-107 does not meet.
• Contact Finish Consideration: Tin plating (200.0µin) on the TS-107-T-AA provides thicker surface protection compared to the gold finish (30.0µin) of the original part, suitable for standard signal and power distribution applications.

Frequently Asked Questions (FAQ)

Q: Can the TS-107-T-AA be used as a direct replacement for the 69190-107 in existing designs?

A: Yes. Both connectors share identical pitch (0.100"), position count (7), single-row configuration, and through-hole mounting. PCB footprints are mechanically compatible. Solder termination is supported by both parts.

Q: What is the difference between the gold and tin contact finishes?

A: The 69190-107 uses gold plating (30.0µin thickness) for enhanced corrosion resistance in high-reliability applications. The TS-107-T-AA uses tin plating (200.0µin thickness), which provides adequate conductivity for standard signal and power applications with thicker surface protection. Selection depends on environmental exposure and application requirements.

Q: Does the TS-107-T-AA support press-fit termination like the original part?

A: No. The TS-107-T-AA is specified for solder termination only. The 69190-107 supports both press-fit and solder options. If press-fit termination is required, alternative parts must be evaluated.

Q: What is the significance of the RoHS compliance difference?

A: The 69190-107 is RoHS non-compliant, while the TS-107-T-AA is ROHS3 compliant. For applications subject to RoHS regulations or customer requirements, the TS-107-T-AA meets current environmental standards. Legacy systems may continue using non-compliant parts where regulations do not apply.

Q: Are the moisture sensitivity levels equivalent?

A: Yes. Both connectors are rated MSL 1 (Unlimited), indicating no moisture sensitivity restrictions for storage, handling, or assembly processes.

Q: What packaging is available for the TS-107-T-AA?

A: The TS-107-T-AA is supplied in tube packaging, suitable for automated assembly and manual component handling.