Amphenol ICC 69155-124 Equivalent & Substitute Parts

Part Overview

The Amphenol ICC 69155-124 is a rectangular connector header featuring a right-angle, through-hole design with 24 positions at 2.54mm pitch. This shrouded, board-to-board connector is part of the Quickie™ series and maintains active product status with 881 units in current inventory. The connector employs male pins with gold-plated circular contacts and phosphor bronze material, suitable for applications requiring reliable board-level interconnection with push-pull fastening.

Substitute parts become necessary when addressing inventory constraints, product lifecycle transitions, or specific compliance requirements. The listed alternatives maintain electrical and mechanical compatibility while offering different feature sets and availability profiles.

Substiute Parts

69155-124

Amphenol ICC (FCI)In Stock: 97969155-124 Datasheet

Current PartRFQ

2-1761605-8

TE Connectivity AMP ConnectorsIn Stock: 10542-1761605-8 Datasheet

MFR RecommendedRFQ

5104340-5

TE Connectivity AMP ConnectorsIn Stock: 7495104340-5 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the 69155-124 is determined by strict alignment with the following core parameters:

• Connector geometry: 24-position, 2-row configuration at 0.100" (2.54mm) pitch with 0.100" row spacing
• Mounting and orientation: Through-hole, right-angle design
• Contact system: Male pin configuration with push-pull fastening
• Shrouding: 4-wall shrouded housing
• Electrical performance: 1A current rating per contact
• Safety compliance: UL94 V-0 flammability rating
• Environmental classification: MSL 1 (Unlimited moisture sensitivity)

The two qualified substitutes—TE Connectivity AMP Connectors 2-1761605-8 and 5104340-5—satisfy these core requirements while differing in product status, contact material composition, insulation material, and compliance certifications.

Parameter Comparison

Engineering Selection Recommendations

Primary Selection: 69155-124 (Amphenol ICC)

The 69155-124 remains the preferred choice for active designs. It maintains active product status with adequate inventory availability and meets all core electrical and mechanical requirements. However, designers should note that this part carries RoHS non-compliant status, which may impact applications subject to RoHS directives.

Secondary Selection: 5104340-5 (TE Connectivity)

The 5104340-5 serves as the recommended substitute for new designs or applications requiring RoHS compliance. This part maintains active product status and provides full compliance with RoHS regulations. The kinked pin termination option and polyphthalamide insulation material offer alternative construction characteristics. Inventory availability is adequate at 644 units. The reduced contact finish thickness (15.0µin versus 30.0µin) and brass contact material represent minor deviations from the primary part but remain within acceptable substitution parameters.

Tertiary Selection: 2-1761605-8 (TE Connectivity)

The 2-1761605-8 is classified as obsolete and should be considered only when existing inventory must be consumed or when legacy system maintenance requires exact historical matching. This part achieves ROHS3 compliance and provides higher contact finish thickness (30.0µin). The obsolete status indicates limited future availability and potential supply chain constraints.

Frequently Asked Questions (FAQ)

Q: Can the 5104340-5 directly replace the 69155-124 in existing designs?

A: Yes. Both parts maintain identical 24-position, 2-row configuration at 0.100" (2.54mm) pitch with through-hole, right-angle mounting and push-pull fastening. The square contact geometry of the 5104340-5 versus the circular contacts of the 69155-124 does not affect mating compatibility. The brass contact material and reduced finish thickness of the 5104340-5 remain within acceptable electrical performance parameters for 1A current rating applications.

Q: What is the significance of the RoHS compliance difference?

A: The 69155-124 is RoHS non-compliant, while the 5104340-5 is RoHS compliant. Applications subject to RoHS directives (EU Directive 2011/65/EU or equivalent regulations) must use RoHS-compliant components. The 5104340-5 satisfies these regulatory requirements.

Q: Why is the 2-1761605-8 listed as obsolete?

A: Obsolete status indicates that the manufacturer has discontinued active production and support. While current inventory exists (1024 units), future availability cannot be guaranteed. This part should be reserved for legacy system maintenance or inventory consumption only.

Q: Are there packaging differences between these parts?

A: The 69155-124 is supplied in bulk packaging, while the 5104340-5 is supplied in tube packaging. The 2-1761605-8 packaging is not specified. Packaging differences do not affect electrical or mechanical compatibility but may influence procurement logistics and handling procedures.

Q: What are the contact finish thickness implications?

A: The 69155-124 and 2-1761605-8 both feature 30.0µin (0.76µm) mating contact finish thickness, while the 5104340-5 provides 15.0µin (0.38µm). Both thicknesses meet standard gold plating specifications for connector applications. The thicker finish of the primary part may offer marginally extended contact life in high-cycle mating applications, but both are suitable for standard board-level interconnection.

Q: Can these parts be intermixed in the same assembly?

A: Yes. All three parts maintain identical mating geometry, pitch, and fastening characteristics. However, design documentation should specify a single part number to ensure manufacturing consistency and traceability. If multiple part numbers are used across production batches, this should be explicitly documented in the bill of materials and assembly procedures.