RF Attenuator 6810.01.A Equivalent & Substitute Parts

Part Overview

The Huber+Suhner 6810.01.A is an RF attenuator module designed for inline applications requiring fixed 10dB attenuation across the 0 Hz to 4 GHz frequency range. This component operates at 1W power handling capacity with 50 Ohm impedance and features BNC connectors for direct integration into RF signal paths. The part maintains Active product status with 722 units available in bulk packaging. Equivalent substitute parts are identified based on matching core electrical specifications: attenuation value, impedance, power rating, and connector type. Alternative models may be required due to inventory constraints, regional availability, or specific packaging preferences while maintaining functional compatibility.

Substiute Parts

6810.01.A

Huber+Suhner, Inc.In Stock: 7326810.01.A Datasheet

Current PartRFQ

R412410124

Radiall USA, Inc.In Stock: 917R412410124 Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the 6810.01.A is determined by strict equivalence across five critical parameters: attenuation value (10dB), impedance (50 Ohms), power handling (1W), connector configuration (BNC In-Line Module), and product status (Active). The identified substitute part R412410124 from Radiall USA, Inc. matches all mandatory electrical parameters. The frequency range specification for R412410124 extends to 3 GHz, which represents a narrower operational bandwidth compared to the 4 GHz upper limit of the primary part. This frequency difference does not disqualify the substitute for applications operating within the 0 Hz to 3 GHz window. Both parts maintain Active status and are available in production quantities.

Parameter Comparison

Engineering Selection Recommendations

Primary Part (6810.01.A): Select this Huber+Suhner component for applications requiring full 4 GHz frequency coverage. REACH Unaffected status applies. Bulk packaging accommodates high-volume integration requirements.

Substitute Part (R412410124): The Radiall USA attenuator is suitable for systems operating within the 0 Hz to 3 GHz frequency band. This part carries ROHS3 Compliant and REACH Affected designations. Box packaging is appropriate for standard procurement workflows. Higher inventory availability (862 units) may support shorter lead times.

Selection Criteria: Choose the 6810.01.A when maximum frequency coverage to 4 GHz is required. Choose R412410124 when operation is limited to 3 GHz or below and ROHS3 compliance is a system requirement. Both parts deliver identical attenuation, impedance, power handling, and connector specifications within their respective frequency ranges.

Frequently Asked Questions (FAQ)

Q: Can R412410124 replace 6810.01.A in all applications?

A: R412410124 is functionally equivalent for applications operating at frequencies up to 3 GHz. Applications requiring operation above 3 GHz up to 4 GHz must use the 6810.01.A.

Q: What are the core electrical equivalencies between these parts?

A: Both parts provide 10dB attenuation, 50 Ohm impedance, 1W power handling, and BNC In-Line Module connectors. These parameters are identical across both components.

Q: Does packaging type affect electrical performance?

A: No. Bulk and Box packaging are logistical variants only. Electrical specifications and performance characteristics remain unchanged.

Q: Are there compliance differences between the two parts?

A: Yes. The 6810.01.A is REACH Unaffected. The R412410124 is REACH Affected and ROHS3 Compliant. System compliance requirements may influence part selection.

Q: Which part should be selected for new designs?

A: For new designs, confirm the maximum operating frequency requirement. If 3 GHz is sufficient, either part is acceptable. If 4 GHz coverage is needed, specify 6810.01.A. Verify compliance certifications against system requirements.

Q: Is inventory availability a factor in substitution decisions?

A: Inventory levels (722 units for 6810.01.A and 862 units for R412410124) may influence procurement timelines but do not affect electrical compatibility or substitution eligibility.