Amphenol ICC 68015-208 Equivalent & Substitute Parts

Part Overview

The Amphenol ICC 68015-208 is a rectangular connector header, right-angle mounted, with 8 positions at 2.54mm pitch. This through-hole component is designed for board-to-board connections using solder termination and push-pull fastening. The part is classified as obsolete, making identification of functionally equivalent alternatives essential for ongoing design support and procurement planning.

Substiute Parts

68015-208

Amphenol ICC (FCI)In Stock: 115168015-208 Datasheet

Current PartRFQ

4-103765-0

TE Connectivity AMP ConnectorsIn Stock: 9274-103765-0 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the Amphenol ICC 68015-208 is constrained by the following critical parameters:

• Pitch - Mating: 0.100" (2.54mm) — must match exactly for mechanical compatibility
• Connector Type: Header with male pin contacts
• Mounting Type: Through hole, right angle configuration
• Termination: Solder
• Fastening Type: Push-pull mechanism
• Contact Material and Finish: Gold-plated contacts for reliable mating
• Current Rating: 3A per contact minimum

The TE Connectivity AMP Connectors 4-103765-0 shares the core electrical and mechanical characteristics required for substitution. However, this part is available in a 40-position configuration, which allows for breakaway or partial-use scenarios where only 8 positions are populated or utilized. The identical pitch, contact geometry, termination method, and fastening type establish functional equivalence for applications requiring 8-position connectivity.

Parameter Comparison

Engineering Selection Recommendations

The TE Connectivity 4-103765-0 serves as a functional equivalent for the Amphenol ICC 68015-208 based on matching electrical and mechanical specifications. Both components are classified as obsolete, indicating limited availability through standard distribution channels. Both maintain UL94 V-0 flammability compliance and MSL 1 moisture sensitivity ratings, suitable for standard storage and handling conditions.

The primary design consideration is the 40-position configuration of the TE Connectivity part versus the 8-position requirement of the original design. The breakaway header design of the TE part permits selective use of individual positions, allowing extraction or isolation of unused contacts to achieve the required 8-position functionality. This approach is standard practice in connector substitution where higher-position-count parts are used in lower-position applications.

Contact finish thickness on the TE part (30.0µin) exceeds that of the original (15.0µin), providing enhanced durability and contact reliability. Both parts employ gold plating on mating surfaces and maintain identical contact geometry and current ratings.

Frequently Asked Questions (FAQ)

Q: Can the TE Connectivity 4-103765-0 directly replace the Amphenol ICC 68015-208 in existing designs?

A: Yes, with design consideration for the 40-position configuration. The core electrical and mechanical parameters—pitch, contact type, mounting style, termination method, and fastening mechanism—are identical. The breakaway header design permits use of only the required 8 positions.

Q: What is the significance of the position count difference?

A: The TE Connectivity part is manufactured as a 40-position header with breakaway capability. For applications requiring only 8 positions, the unused positions can be left unpopulated during assembly or mechanically separated if the design permits. The mating interface and contact specifications remain unchanged.

Q: Are there compliance or certification differences between these parts?

A: Both parts carry UL94 V-0 flammability ratings and MSL 1 moisture sensitivity levels. Both are RoHS non-compliant and carry EAR99 ECCN classification. The TE part provides documented operating temperature range (-65°C ~ 105°C), whereas the original part does not specify this parameter.

Q: How do the contact materials differ?

A: The original uses phosphor bronze contacts; the TE substitute uses copper alloy. Both materials are standard for this connector class and provide equivalent electrical performance. The TE part's thicker gold plating (30.0µin vs. 15.0µin) compensates for any material differences and enhances contact longevity.

Q: What should be verified before implementing this substitution?

A: Confirm that the PCB layout and mating connector are compatible with the 2.54mm pitch standard. Verify that the right-angle mounting orientation and through-hole solder termination match the existing design. Assess whether the 40-position breakaway configuration can be accommodated in the available board space or if selective position use is acceptable.