Amphenol ICC 65823-061 Rectangular Connector - Equivalent & Substitute Parts

Part Overview

The Amphenol ICC 65823-061 is an active-status rectangular connector header designed for through-hole, right-angle board-to-cable/wire applications. This 16-position, 2-row connector with 0.100" (2.54mm) pitch and shrouded 4-wall design serves as a standard interconnect component in electronic assemblies. Substitute parts are identified to provide alternative sourcing options when the primary part is unavailable or when design requirements permit equivalent configurations.

Substiute Parts

65823-061

Amphenol ICC (FCI)In Stock: 70665823-061 Datasheet

Current PartRFQ

499141-3

TE Connectivity AMP ConnectorsIn Stock: 719499141-3 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the Amphenol ICC 65823-061 is determined by strict alignment of the following critical parameters:

• Connector Type & Contact Type: Header with Male Pin contacts
• Position Configuration: 16 positions in 2-row arrangement
• Pitch Specification: 0.100" (2.54mm) mating pitch and row spacing
• Mounting & Orientation: Through-hole, right-angle mounting
• Shrouding Design: Shrouded 4-wall configuration
• Termination Method: Solder termination
• Fastening Mechanism: Latch lock/eject hooks
• Compliance Rating: UL94 V-0 flammability classification

The substitute part TE Connectivity AMP Connectors 499141-3 meets all critical substitution criteria. Variations in contact material, contact finish composition, insulation material specification, and operating temperature range do not preclude functional equivalence when the above parameters align.

Parameter Comparison

Engineering Selection Recommendations

Both the Amphenol ICC 65823-061 and TE Connectivity 499141-3 maintain active product status and carry identical export control classifications (ECCN EAR99) and tariff codes (HTSUS 8536.69.4040). Both components are subject to REACH regulations and carry unlimited moisture sensitivity ratings.

The Amphenol ICC 65823-061 is RoHS non-compliant. The TE Connectivity 499141-3 carries a "Not applicable" RoHS status designation. Design environments with RoHS compliance requirements must evaluate this distinction against applicable regulatory frameworks.

Both parts satisfy UL94 V-0 flammability requirements and are suitable for equivalent electrical and mechanical applications where the specified connector pitch, position count, mounting orientation, and shrouding configuration are required.

Frequently Asked Questions (FAQ)

Q: Can the TE Connectivity 499141-3 be used as a direct replacement for the Amphenol ICC 65823-061?

A: Yes, when the application requires a 16-position, 2-row header connector with 0.100" (2.54mm) pitch, through-hole right-angle mounting, shrouded 4-wall design, and solder termination. Both parts share identical mating pitch, row spacing, position configuration, mounting type, and fastening mechanism.

Q: What are the key differences between these two parts?

A: The parts differ in contact material (Phosphor Bronze Alloy vs. Brass), contact finish composition, insulation material specification, contact shape (Circular vs. Square), insulation color, and operating temperature range. The TE Connectivity part specifies operating temperature (-65°C ~ 105°C), current rating (1A per contact), and voltage rating (250VAC), while these parameters are not specified for the Amphenol ICC part.

Q: Are there any compliance considerations when substituting between these parts?

A: The Amphenol ICC 65823-061 is RoHS non-compliant, while the TE Connectivity 499141-3 carries a "Not applicable" RoHS status. Applications subject to RoHS directives must verify compliance requirements against the specific regulatory framework applicable to the end product.

Q: Do both parts use the same packaging format?

A: Yes, both parts are supplied in bulk packaging and carry identical moisture sensitivity level (MSL 1 - Unlimited) ratings.

Q: What determines whether a connector can substitute for the 65823-061?

A: Substitution requires matching the connector type (Header), contact type (Male Pin), position count (16), row configuration (2 rows), mating pitch (0.100" / 2.54mm), row spacing (0.100" / 2.54mm), mounting type (Through Hole, Right Angle), shrouding design (Shrouded - 4 Wall), termination method (Solder), and fastening mechanism (Latch Lock/Eject Hooks).