4PCV-07-006 Equivalent & Substitute Parts

Part Overview

The 4PCV-07-006 is a 7-circuit barrier block connector manufactured by TE Connectivity AMP Connectors. This terminal block features a 0.325" (8.26mm) pitch with screw termination on the top and PC pin termination on the bottom. The connector is rated for 20A at 150V and accommodates wire gauges from 12-22 AWG. The product is currently active and in stock with 804 units available. Substitute parts are identified when equivalent electrical and mechanical specifications are available from alternative manufacturers, enabling procurement flexibility and supply chain continuity.

Substiute Parts

4PCV-07-006

TE Connectivity AMP ConnectorsIn Stock: 8704PCV-07-006 Datasheet

Current PartRFQ

A102207

Eaton - Electronics DivisionIn Stock: 920A102207 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the 4PCV-07-006 is determined by the following critical parameters:

Core Electrical Compatibility:

• Number of circuits: 7
• Pitch: 0.325" (8.26mm)
• Current rating: 20A minimum
• Voltage rating: 150V minimum
• Wire gauge accommodation: must support 12-22 AWG range

Mechanical Compatibility:

• Terminal block type: Barrier block
• Top termination: Screw-based
• Bottom termination: PC pin
• Mounting type: Through hole
• Number of rows: 1

Regulatory & Environmental:

• Material flammability rating: UL94 V-0
• RoHS compliance status
• Operating temperature range: minimum 105°C upper limit

The substitute part A102207 meets all core electrical and mechanical requirements. Differences in barrier wall configuration (3-wall vs. 2-wall), voltage rating (250V vs. 150V), and wire gauge lower limit (14 AWG vs. 12 AWG) do not preclude substitution when the application requirements fall within the substitute's specifications.

Parameter Comparison

Engineering Selection Recommendations

4PCV-07-006 (TE Connectivity AMP Connectors) is the primary specification. This part is active, RoHS compliant, and maintains full compliance with the stated electrical and mechanical requirements. The 3-wall barrier configuration and captive plate screw termination provide the specified design features. This part is recommended for applications requiring 12 AWG wire accommodation and the specific barrier wall configuration.

A102207 (Eaton - Electronics Division) is a qualified substitute for applications where the following conditions are met:

• Wire gauge requirement does not include 12 AWG (application uses 14-22 AWG range only)
• Operating temperature range of -40°C to 105°C is acceptable
• 2-wall barrier configuration meets circuit isolation requirements
• Higher voltage rating (250V) is acceptable for the application
• Screw termination without captive plate is functionally acceptable

Both parts are active products with current inventory availability. Both meet UL94 V-0 flammability requirements and RoHS compliance standards. Selection between these parts depends on specific application wire gauge requirements and barrier configuration needs.

Frequently Asked Questions (FAQ)

Q: Can A102207 be used in place of 4PCV-07-006 in all applications?

A: No. The A102207 accommodates wire gauges 14-22 AWG, while the 4PCV-07-006 accommodates 12-22 AWG. If the application requires 12 AWG wire termination, only the 4PCV-07-006 is suitable. For applications using 14-22 AWG wire, A102207 is compatible.

Q: What is the difference between 3-wall and 2-wall barrier configurations?

A: The 4PCV-07-006 features a 3-wall (tri) barrier design, while the A102207 features a 2-wall (dual) barrier design. Both configurations meet UL94 V-0 flammability ratings. The barrier wall configuration affects circuit isolation geometry. Application-specific isolation requirements determine which configuration is appropriate.

Q: Is the captive plate screw termination feature critical for substitution?

A: The 4PCV-07-006 includes a captive plate on the screw termination, while the A102207 uses standard screws without a captive plate. Both provide screw-based termination. The captive plate prevents screw loss during assembly. If screw retention is a design requirement, the 4PCV-07-006 is necessary. If standard screw termination is acceptable, A102207 is compatible.

Q: Are both parts suitable for the same PCB mounting applications?

A: Yes. Both parts feature through-hole mounting, 0.325" (8.26mm) pitch, 7 circuits, and PC pin bottom termination. PCB footprints are identical. Both parts are suitable for the same through-hole mounting applications.

Q: What is the significance of the voltage rating difference (150V vs. 250V)?

A: The 4PCV-07-006 is rated for 150V, while the A102207 is rated for 250V. A higher voltage rating indicates the part can safely operate at higher voltages. For applications operating at 150V or below, the A102207 (250V rated) is acceptable. The higher rating does not create compatibility issues for lower-voltage applications.

Q: Do both parts meet current regulatory compliance requirements?

A: Yes. The 4PCV-07-006 is RoHS compliant. The A102207 is ROHS3 compliant, which represents a more recent revision of the RoHS standard. Both parts meet current regulatory requirements. ROHS3 compliance indicates the A102207 meets updated environmental standards.

Q: What is the operating temperature range for each part?

A: The 4PCV-07-006 operates at a maximum of 105°C. The A102207 operates across a range of -40°C to 105°C. For applications requiring operation below 0°C, only the A102207 is suitable. For standard room-temperature to 105°C applications, both parts are compatible.

Q: Can these parts be intermixed in the same assembly?

A: Both parts have identical pitch (0.325"), circuit count (7), and mounting type (through hole). They can be used in the same assembly if application requirements are met for each position. However, mixing parts with different wire gauge capabilities (12 AWG vs. 14 AWG minimum) requires verification that each position's wire gauge requirement is satisfied by the selected part.