2SD1899-M-TP Equivalent & Substitute Parts

Part Overview

The 2SD1899-M-TP is an NPN bipolar junction transistor manufactured by Micro Commercial Co, rated for 60V collector-emitter breakdown voltage and 3A maximum collector current. This component is classified as obsolete, necessitating identification of equivalent substitute parts for ongoing production and maintenance applications. The part is housed in a TO-252-3 DPAK surface mount package and operates across a temperature range of -55°C to 150°C.

Substiute Parts

2SD1899-M-TP

Micro Commercial CoIn Stock: 10852SD1899-M-TP Datasheet

Current PartRFQ

2SC6097-TL-E

onsemiIn Stock: 133742SC6097-TL-E Datasheet

SimilarRFQ

2SD1802T-TL-E

onsemiIn Stock: 88352SD1802T-TL-E Datasheet

SimilarRFQ

2SD2318TLU

Rohm SemiconductorIn Stock: 35082SD2318TLU Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the 2SD1899-M-TP is determined by the following critical electrical and mechanical parameters:

Primary Matching Criteria:

• Transistor type: NPN configuration
• Collector current rating: 3A maximum
• Collector-emitter breakdown voltage: 60V minimum
• Package type: TO-252-3 DPAK surface mount
• RoHS3 compliance
• Moisture sensitivity level: 1 (Unlimited)

Secondary Compatibility Factors:

• DC current gain (hFE) characteristics
• Saturation voltage (Vce) performance
• Transition frequency capability
• Power dissipation rating
• Operating temperature range

The substitute parts listed below meet the primary matching criteria and are therefore electrically and mechanically compatible with the 2SD1899-M-TP in applications where the specified electrical parameters are within acceptable design tolerances.

Parameter Comparison

Engineering Selection Recommendations

2SC6097-TL-E (onsemi): This part is an active product with full RoHS3 compliance and REACH unaffected status. It matches the 60V breakdown voltage and 3A collector current specifications. The 2SC6097-TL-E exhibits superior transition frequency (390MHz) and lower saturation voltage (135mV), making it suitable for applications requiring improved switching performance. Power dissipation is rated at 800mW, which is lower than the original part. This substitute is recommended for new designs and ongoing production where active component availability is required.

2SD1802T-TL-E (onsemi): This part is an active product with full RoHS3 compliance and REACH unaffected status. It matches the 3A collector current specification but operates at a reduced maximum breakdown voltage of 50V. The 2SD1802T-TL-E maintains 1W power dissipation and provides 150MHz transition frequency. This substitute is suitable for applications where the 50V voltage rating is acceptable and active component sourcing is prioritized.

2SD2318TLU (Rohm Semiconductor): This part carries a "Not For New Designs" status and is therefore not recommended for new product development. However, it remains available for legacy system maintenance and repair. The 2SD2318TLU matches both the 60V breakdown voltage and 3A collector current specifications. It provides significantly higher power dissipation (15W) and lower transition frequency (50MHz), making it suitable only for low-frequency, high-power applications where the original 2SD1899-M-TP characteristics are not critical.

Frequently Asked Questions (FAQ)

Q: Can the 2SC6097-TL-E directly replace the 2SD1899-M-TP in all applications?

A: The 2SC6097-TL-E is electrically compatible based on matching collector current (3A) and collector-emitter breakdown voltage (60V) specifications. Both parts use identical TO-252-3 DPAK packaging. However, the 2SC6097-TL-E has lower maximum power dissipation (800mW versus 1W). Verify that your application does not exceed 800mW continuous power dissipation before substitution.

Q: Why does the 2SD1802T-TL-E have a lower breakdown voltage rating?

A: The 2SD1802T-TL-E is rated for 50V maximum collector-emitter breakdown voltage, compared to 60V for the 2SD1899-M-TP. This part is suitable only for applications where the circuit operates below 50V. Do not use this substitute in circuits designed for 60V operation.

Q: Is the 2SD2318TLU suitable for new product designs?

A: No. The 2SD2318TLU carries a "Not For New Designs" product status. This part is available only for maintenance and repair of existing systems. For new designs, use either the 2SC6097-TL-E or 2SD1802T-TL-E, both of which have active product status.

Q: Are all substitute parts RoHS3 compliant?

A: Yes. All three substitute parts (2SC6097-TL-E, 2SD1802T-TL-E, and 2SD2318TLU) are RoHS3 compliant and carry moisture sensitivity level 1 (Unlimited), matching the original 2SD1899-M-TP specifications.

Q: What is the primary difference between the 2SC6097-TL-E and 2SD1802T-TL-E?

A: The 2SC6097-TL-E operates at 60V breakdown voltage with 390MHz transition frequency, while the 2SD1802T-TL-E operates at 50V breakdown voltage with 150MHz transition frequency. The 2SC6097-TL-E is optimized for higher-frequency switching applications, whereas the 2SD1802T-TL-E is suitable for lower-voltage circuits with moderate switching speeds.

Q: Can I use the 2SD2318TLU in high-frequency applications?

A: No. The 2SD2318TLU has a transition frequency of 50MHz, significantly lower than the original 2SD1899-M-TP (120MHz). This part is designed for low-frequency, high-power applications and is not suitable for circuits requiring switching frequencies above 50MHz.

Q: Are the package dimensions identical across all substitute parts?

A: Yes. All parts use the TO-252-3 DPAK (2 Leads + Tab) surface mount package, designated as SC-63. The physical dimensions and PCB footprint are identical, allowing direct mechanical substitution without layout modifications.