TE Connectivity 2176092-8 Equivalent & Substitute Parts

Part Overview

The TE Connectivity 2176092-8 is a thin film chip resistor with a resistance value of 787 Ohms and a tolerance of ±0.1%. This 0805 (2012 Metric) package component is rated for 0.25W (1/4W) power dissipation and operates across a temperature range of -55°C to 155°C. The part is manufactured in the RP73P series by TE Connectivity's Holsworthy facility and maintains Active product status with ROHS3 compliance and unlimited moisture sensitivity rating (MSL 1).

Equivalent and substitute parts are necessary when the primary component becomes unavailable, when supply chain optimization is required, or when design specifications allow for alternative manufacturers while maintaining electrical and mechanical compatibility.

Substiute Parts

2176092-8

TE Connectivity Passive ProductIn Stock: 14802176092-8 Datasheet

Current PartRFQ

ERA-6AEB7870V

Panasonic Electronic ComponentsIn Stock: 15821ERA-6AEB7870V Datasheet

DirectRFQ

RG2012N-7870-B-T5

SusumuIn Stock: 6101RG2012N-7870-B-T5 Datasheet

DirectRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the TE Connectivity 2176092-8 is determined by strict adherence to the following electrical and mechanical parameters:

Critical Matching Parameters:

• Resistance value: 787 Ohms (exact match required)
• Tolerance: ±0.1% (exact match required)
• Package type: 0805 (2012 Metric) (exact match required)
• Composition: Thin Film (exact match required)
• Operating temperature range: -55°C to 155°C (minimum requirement)
• RoHS compliance: ROHS3 (minimum requirement)

Allowable Variation Parameters:

• Power rating: Substitute parts may have equal or lower power ratings, provided the application does not exceed the substitute's power dissipation capability
• Temperature coefficient: Substitute parts may have equal or tighter specifications
• Height (seated): Substitute parts may have equal or lower maximum heights
• Manufacturer and series designation: May vary without affecting substitution validity

The substitute parts listed below meet all critical matching parameters and maintain compatibility with the original component's electrical and mechanical specifications.

Parameter Comparison

Engineering Selection Recommendations

Both substitute parts maintain full electrical compatibility with the TE Connectivity 2176092-8 across all critical parameters: resistance value, tolerance, package type, composition, operating temperature range, and RoHS compliance status.

Panasonic ERA-6AEB7870V is suitable for applications where automotive-grade qualification (AEC-Q200) is required or preferred. This part carries the same temperature coefficient specification as the original component and maintains identical operating temperature limits.

Susumu RG2012N-7870-B-T5 provides enhanced specifications through a tighter temperature coefficient (±10ppm/°C versus ±25ppm/°C) and includes anti-sulfur protection. This part also carries AEC-Q200 automotive qualification. The reduced maximum seated height (0.020" versus 0.026") may provide advantages in space-constrained applications.

Both substitute parts are rated at 0.125W (1/8W) power dissipation, which is lower than the original 0.25W rating. Applications requiring the full 0.25W power dissipation capability of the original component cannot use these substitutes without thermal analysis to confirm adequate margin.

All three parts maintain Active product status and are available in Tape & Reel packaging with unlimited moisture sensitivity rating.

Frequently Asked Questions (FAQ)

Q: Can the Panasonic ERA-6AEB7870V or Susumu RG2012N-7870-B-T5 be used as direct replacements for the TE Connectivity 2176092-8?

A: Both parts are electrically and mechanically compatible substitutes for applications where the power dissipation requirement does not exceed 0.125W. The resistance value, tolerance, package type, composition, and operating temperature range are identical. If your application requires the full 0.25W power rating of the original component, these substitutes are not suitable without thermal analysis.

Q: What is the difference between the two substitute parts?

A: Both parts share identical resistance, tolerance, package, and operating temperature specifications. The Susumi RG2012N-7870-B-T5 offers a tighter temperature coefficient (±10ppm/°C versus ±25ppm/°C) and includes anti-sulfur protection. The Susumu part also has a lower maximum seated height (0.020" versus 0.024"). Both carry AEC-Q200 automotive qualification.

Q: Are these substitute parts suitable for automotive applications?

A: Both substitute parts carry AEC-Q200 automotive qualification. The original TE Connectivity part does not specify automotive qualification. If your application requires AEC-Q200 compliance, the substitute parts provide this certification.

Q: Will the substitute parts fit in the same PCB footprint as the original component?

A: Yes. All three parts use the identical 0805 (2012 Metric) package with the same length (0.079") and width (0.049") dimensions. The substitute parts have lower maximum seated heights (0.024" and 0.020" respectively versus 0.026"), which ensures compatibility with PCB layouts designed for the original component.

Q: What is the significance of the ±0.1% tolerance specification?

A: The ±0.1% tolerance indicates a precision thin film resistor. All three parts maintain this identical tolerance, ensuring that substitution does not affect circuit performance in applications requiring high-precision resistance values.

Q: Are all three parts RoHS compliant?

A: Yes. The TE Connectivity 2176092-8, Panasonic ERA-6AEB7870V, and Susumu RG2012N-7870-B-T5 are all ROHS3 compliant and carry unlimited moisture sensitivity rating (MSL 1).