Rosenberger 210135 SMP Longwipe Straight Plug PCB Coaxial Connector

Part Overview

The Rosenberger 210135 is an SMP Longwipe straight plug coaxial connector designed for surface mount PCB applications. This male pin connector operates at 50 Ohms impedance and is rated for RF frequencies up to 6 GHz. The connector features solder termination for both center contact and shield, with a snap-on fastening mechanism and limited detent design. The part is currently active in production with 1091 units in stock. Equivalent substitute parts may be required due to design constraints, PCB layout requirements, or connector orientation specifications in target applications.

Substiute Parts

210135

RosenbergerIn Stock: 1136210135 Datasheet

Current PartRFQ

17S202-40ML5

RosenbergerIn Stock: 113717S202-40ML5 Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

The Rosenberger 17S202-40ML5 is identified as a parametric equivalent to the 210135 based on the following critical substitution criteria:

Matching Parameters:

• Connector Style: SMP, Longwipe
• Connector Type: Plug, Male Pin
• Impedance: 50 Ohms
• Mounting Type: Surface Mount
• Contact Termination: Solder
• Shield Termination: Solder
• Fastening Type: Snap-On
• Frequency - Max: 6 GHz
• Number of Ports: 1
• Features: Limited Detent
• Housing Color: Gold
• Operating Temperature Range: -65°C to 155°C
• Voltage Rating: 335 V
• Mating Cycles: 500
• RoHS Compliance: Confirmed
• Moisture Sensitivity Level (MSL): 1 (Unlimited)

Distinguishing Characteristic: The primary difference between these parts is connector orientation. The 210135 is a straight plug configuration, while the 17S202-40ML5 is a right-angle plug configuration. This distinction determines suitability based on PCB layout and mechanical space constraints.

Parameter Comparison

Engineering Selection Recommendations

Both the Rosenberger 210135 and 17S202-40ML5 are active production parts with confirmed RoHS compliance and unlimited moisture sensitivity rating. Selection between these parts is determined by mechanical orientation requirements:

Select 210135 (Straight Plug) when:

• PCB layout requires axial connector orientation perpendicular to the board surface
• Mating interface is positioned directly above the solder pads
• Space constraints allow vertical connector extension

Select 17S202-40ML5 (Right Angle Plug) when:

• PCB layout requires connector orientation parallel to the board surface
• Mating interface is positioned at the board edge or side
• Space constraints require low-profile connector mounting

Both parts maintain identical electrical performance at 50 Ohms impedance, 6 GHz maximum frequency, 335 V voltage rating, and 500 mating cycles. Material composition differences (LCP versus PTFE dielectric, Brass versus Bronze center contact) do not affect functional equivalence for standard RF applications within specified operating parameters.

Frequently Asked Questions (FAQ)

Q: Can the 17S202-40ML5 right-angle connector be used as a direct replacement for the 210135 straight connector?

A: The 17S202-40ML5 is electrically equivalent but mechanically different. Substitution is valid only if the PCB layout and mating interface accommodate right-angle orientation. Connector orientation is a design-critical parameter that cannot be overlooked.

Q: Are there electrical performance differences between these two connectors?

A: No. Both connectors operate at 50 Ohms impedance, support frequencies to 6 GHz, and maintain identical voltage and temperature ratings. Dielectric material differences (LCP versus PTFE) and center contact material differences (Brass versus Bronze) do not affect electrical performance within specified operating ranges.

Q: What is the significance of the dielectric material difference?

A: The 210135 uses Liquid Crystal Polymer (LCP) dielectric, while the 17S202-40ML5 uses Polytetrafluoroethylene (PTFE). Both materials are suitable for RF applications at 6 GHz. Material selection is determined by the connector design and does not impact substitution eligibility for equivalent electrical performance.

Q: Are both connectors RoHS compliant?

A: Yes. The 210135 is ROHS3 compliant, and the 17S202-40ML5 is RoHS compliant. Both meet regulatory requirements for hazardous substance restrictions.

Q: What is the moisture sensitivity level for these connectors?

A: Both connectors have Moisture Sensitivity Level (MSL) 1, which indicates unlimited shelf life without moisture control requirements. Standard storage conditions are acceptable.

Q: How many mating cycles are these connectors rated for?

A: Both the 210135 and 17S202-40ML5 are rated for 500 mating cycles, indicating equivalent mechanical durability and connector lifespan.

Q: Are both connectors available in stock?

A: Yes. The 210135 has 1091 units in stock, and the 17S202-40ML5 has 1058 units in stock, both listed as new original inventory.