DIP Switch SPST 206-6LPST Equivalent & Substitute Parts

Part Overview

The CTS Electrocomponents 206-6LPST is a 6-position DIP switch with SPST (Single Pole Single Throw) circuit configuration, rated for 50mA at 24VDC. This through-hole mounted component features a slide actuator with gold-plated contacts and is designed for applications requiring reliable switching in compact form factors. The part is currently active in production and ROHS3 compliant. Alternative equivalent parts may be required due to inventory constraints, specific actuator type preferences, or enhanced electrical ratings for demanding applications.

Substiute Parts

206-6LPST

CTS ElectrocomponentsIn Stock: 880206-6LPST Datasheet

Current PartRFQ

76RSB06ST

Grayhill Inc.In Stock: 277376RSB06ST Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

The Grayhill Inc. 76RSB06ST qualifies as a functional equivalent based on the following shared core parameters:

• SPST circuit configuration (single pole, single throw operation)
• 6-position DIP switch architecture
• Through-hole mounting with 0.100" (2.54mm) pitch
• Gold-plated contacts for reliable signal transmission
• Flush/recessed actuator level
• PC pin termination style
• Washable design with tape seal features
• ROHS3 compliance and REACH unaffected status
• Identical HTSUS classification (8536.50.9065)

The 76RSB06ST provides enhanced electrical performance with 150mA current rating and 30VDC voltage rating, exceeding the 206-6LPST specifications. The primary design difference is the rocker actuator type versus the slide actuator on the main part, which affects user interface but not electrical compatibility in fixed-position applications.

Parameter Comparison

Engineering Selection Recommendations

Both parts meet ROHS3 compliance and REACH unaffected requirements, qualifying them for equivalent use in regulated applications. The 206-6LPST provides superior electrical cycle life (10,000 cycles versus 2,000 cycles) and extended low-temperature operation (-55°C versus -40°C minimum). The 76RSB06ST offers higher current and voltage ratings, making it suitable for applications requiring greater electrical headroom. Actuator type selection depends on mechanical interface requirements: slide actuators provide linear positioning feedback, while rocker actuators offer tactile switching action. Both parts maintain compatible footprints and pitch specifications for direct PCB layout substitution.

Frequently Asked Questions (FAQ)

Q: Can the 76RSB06ST replace the 206-6LPST in all applications?

A: The 76RSB06ST is electrically compatible for applications operating within 24VDC and 50mA specifications. The rocker actuator differs mechanically from the slide actuator, which may affect user interface or mechanical constraints in the end application. Verify actuator accessibility and mechanical clearance requirements before substitution.

Q: What are the key differences between these DIP switches?

A: The primary differences are actuator type (slide versus rocker), electrical cycle life (10,000 versus 2,000 cycles), and operating temperature minimum (-55°C versus -40°C). The 76RSB06ST provides higher current and voltage ratings. Both maintain identical pitch, position count, and circuit configuration.

Q: Are both parts suitable for washable PCB applications?

A: Yes. Both the 206-6LPST and 76RSB06ST feature washable designs with tape seal features, supporting standard PCB cleaning processes.

Q: What is the impact of different electrical life ratings?

A: The 206-6LPST is rated for 10,000 electrical cycles, while the 76RSB06ST is rated for 2,000 cycles. For applications with frequent switch position changes, the 206-6LPST provides extended operational life. For fixed or infrequent position changes, both parts are suitable.

Q: Do these parts require different PCB footprints?

A: No. Both parts share identical 0.100" (2.54mm) pitch and through-hole PC pin termination, allowing direct footprint compatibility. Physical dimensions are nearly identical (height and length differences are less than 0.01 inches), supporting direct PCB layout substitution.