TE Connectivity AMP Connectors 133795-1 Equivalent & Substitute Parts

Part Overview

The TE Connectivity AMP Connectors 133795-1 is an N Type Connector Plug with male pin configuration, designed for 50 Ohm coaxial RF applications. This panel mount connector features solder termination for both center contact and shield, operating across a frequency range up to 11 GHz. The part is currently active in production with 1109 pieces available in new original stock. Equivalent and substitute parts are identified to provide alternative sourcing options when the primary part is unavailable or when procurement requirements necessitate alternative manufacturers.

Substiute Parts

133795-1

TE Connectivity AMP ConnectorsIn Stock: 1141133795-1 Datasheet

Current PartRFQ

13_N-50-0-1/133_NE

Huber+Suhner, Inc.In Stock: 108913_N-50-0-1/133_NE Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of coaxial RF connectors is determined by strict equivalence across electrical and mechanical parameters. The following criteria establish substitutability for the TE Connectivity 133795-1:

Electrical Parameters: Impedance must be 50 Ohms. Frequency maximum rating must be 11 GHz or greater. Voltage rating must be 1000 V or greater. Mating cycle rating must be 500 or greater.

Mechanical Parameters: Connector style must be N Type. Connector type must be Plug with Male Pin configuration. Contact termination must be Solder. Shield termination must be Solder. Mounting type must be Panel Mount. Mounting feature must be Flange. Fastening type must be Threaded. Number of ports must be 1.

Environmental Parameters: Operating temperature range must encompass -65°C to 165°C. Moisture sensitivity level must be 1 (Unlimited) or Not Applicable.

The substitute part 13_N-50-0-1/133_NE from Huber+Suhner, Inc. meets all specified electrical and mechanical parameters and is therefore classified as a parametric equivalent.

Parameter Comparison

Engineering Selection Recommendations

Both the TE Connectivity 133795-1 and the Huber+Suhner 13_N-50-0-1/133_NE are active production parts with identical electrical and mechanical specifications. Selection between these parts should be based on the following factors:

Compliance Status: The TE Connectivity 133795-1 is RoHS non-compliant. The Huber+Suhner 13_N-50-0-1/133_NE is ROHS3 compliant. Applications requiring RoHS compliance must use the Huber+Suhner part.

REACH Status: The TE Connectivity 133795-1 has undefined REACH status. The Huber+Suhner 13_N-50-0-1/133_NE is REACH unaffected. Applications subject to REACH regulations should prioritize the Huber+Suhner part.

Material Specifications: The TE Connectivity part does not specify center contact material or body material. The Huber+Suhner part specifies brass body material with white bronze finish and PFA/PTFE dielectric material. Applications requiring documented material specifications should use the Huber+Suhner part.

Inventory Availability: TE Connectivity 133795-1: 1109 pieces in stock. Huber+Suhner 13_N-50-0-1/133_NE: 1013 pieces in stock. Both parts maintain adequate inventory levels.

Frequently Asked Questions (FAQ)

Q: Can the Huber+Suhner 13_N-50-0-1/133_NE be used as a direct replacement for the TE Connectivity 133795-1?

A: Yes. Both parts are N Type connector plugs with male pin configuration, 50 Ohm impedance, solder termination, panel mount flange, threaded fastening, 11 GHz maximum frequency, 1000 V voltage rating, and 500 mating cycles. All electrical and mechanical parameters are identical.

Q: What is the difference in RoHS compliance between these parts?

A: The TE Connectivity 133795-1 is RoHS non-compliant. The Huber+Suhner 13_N-50-0-1/133_NE is ROHS3 compliant. Applications subject to RoHS directives must use the Huber+Suhner part.

Q: Are there material differences between these connectors?

A: The Huber+Suhner part specifies brass body material with white bronze finish and PFA/PTFE dielectric material. The TE Connectivity part does not provide these material specifications in the available documentation.

Q: Do both parts operate across the same temperature range?

A: Yes. Both parts operate from -65°C to 165°C.

Q: What is the packaging format for both parts?

A: Both parts are supplied in bulk packaging.

Q: Are there differences in mating cycle ratings?

A: No. Both parts are rated for 500 mating cycles.

Q: Which part should be selected for new designs?

A: Selection should be based on compliance requirements. For applications requiring RoHS compliance, use the Huber+Suhner 13_N-50-0-1/133_NE. For applications with no compliance restrictions, either part is suitable based on availability and procurement preferences.

Q: Do both connectors support the same frequency range?

A: Yes. Both parts support operation up to 11 GHz maximum frequency.