LAPP 10422200 Equivalent & Substitute Parts Reference

Part Overview

The LAPP 10422200 is an EPIC® HB series heavy duty connector base designed for panel mount applications with 90° side entry configuration. This component functions as the receptacle housing for industrial connector systems requiring IP65 ingress protection in harsh environments. The part maintains active product status with 983 units in current inventory stock.

Substitute parts are identified when equivalent functional performance can be achieved through alternative manufacturers while maintaining compatibility with the connector interface requirements and environmental specifications of the application.

Substiute Parts

10422200

LAPPIn Stock: 105210422200 Datasheet

Current PartRFQ

09200030327

HARTINGIn Stock: 127009200030327 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

The HARTING 09200030327 is identified as a substitute based on the following substitution criteria:

Compatible Parameters:

• Heavy duty connector base category with panel mount configuration
• Locking clip retention mechanism on base bottom
• Industrial-grade housing material (thermoplastic vs. zinc die cast)
• EAR99 export classification alignment
• HTSUS commodity code alignment (8538.90.8180)

Functional Equivalence Basis: Both parts function as connector base housings for industrial applications. The HARTING part provides equivalent mechanical interface and retention functionality through comparable locking mechanisms and panel mount design.

Limitations and Differences: The HARTING 09200030327 operates under different electrical and environmental specifications that must be evaluated for specific application requirements. Substitution validity depends on whether the application can accommodate these parameter variations.

Parameter Comparison

Engineering Selection Recommendations

LAPP 10422200 Selection Criteria:

• Applications requiring IP65 ingress protection with dust-tight and water-resistant sealing
• Side entry cable routing requirements
• Operating environments with maximum temperatures to 100°C
• Applications benefiting from zinc die cast construction with powder coat corrosion protection
• EPIC® HB series connector ecosystem compatibility

HARTING 09200030327 Selection Criteria:

• Applications compatible with IP44 ingress protection level
• Bottom entry cable routing requirements
• Operating environments with maximum temperatures to 125°C
• Applications where thermoplastic housing material is acceptable
• Han® A series connector ecosystem compatibility
• RoHS3 compliance requirement
• REACH compliance requirement

Substitution Feasibility: Substitution between these parts requires verification that the application can accommodate differences in ingress protection rating, cable entry direction, connector series interface, and housing material. The parts are not direct functional equivalents due to these parameter variations.

Frequently Asked Questions (FAQ)

Q: Can HARTING 09200030327 directly replace LAPP 10422200 in existing installations?

A: Direct replacement is not supported without application redesign. The parts differ in cable entry direction (side vs. bottom), ingress protection rating (IP65 vs. IP44), connector series (EPIC® HB vs. Han® A), and housing material (zinc die cast vs. thermoplastic). Panel cutouts, mating connector compatibility, and environmental sealing requirements must be re-evaluated.

Q: What is the primary difference in environmental protection between these parts?

A: The LAPP 10422200 provides IP65 rating (dust tight, water resistant), while the HARTING 09200030327 provides IP44 rating (splash protected). Applications exposed to direct water jets or complete dust ingress require the higher IP65 rating of the LAPP part.

Q: Are these parts compatible with the same mating connectors?

A: No. The LAPP part belongs to the EPIC® HB series, while the HARTING part belongs to the Han® A series. These are separate connector ecosystems with different mating interfaces. Mating connectors are series-specific and not interchangeable.

Q: What are the packaging considerations for bulk ordering?

A: Both parts are supplied in bulk packaging. LAPP 10422200 has 983 units in current stock. HARTING 09200030327 has 1224 units in current stock. Bulk packaging specifications should be confirmed with the supplier for specific application requirements.

Q: Does the operating temperature difference affect substitution decisions?

A: The HARTING part supports higher maximum temperature (125°C vs. 100°C). If the application operates below 100°C, this difference is not a limiting factor. If the application requires operation above 100°C, only the HARTING part is suitable. The minimum temperature of -40°C is identical for both parts.

Q: What compliance certifications apply to substitution decisions?

A: Both parts share identical ECCN (EAR99) and HTSUS (8538.90.8180) classifications. The HARTING part includes RoHS3 compliance and REACH unaffected status. Regulatory compliance requirements for the specific application must be verified against these certifications.