HARTING 09662537613 D-Sub Receptacle 15-Position Right Angle Solder Connector

Part Overview

The HARTING 09662537613 is a 15-position D-Sub receptacle connector with female sockets, configured for right-angle through-hole solder termination. This connector is designed for applications requiring reliable signal transmission in industrial and commercial equipment. The part is currently active in production with 984 units in stock. Equivalent and substitute parts are identified based on matching electrical performance, mechanical compatibility, and environmental ratings to support procurement flexibility and supply chain continuity.

Substiute Parts

09662537613

HARTINGIn Stock: 100209662537613 Datasheet

Current PartRFQ

3-106506-2

TE Connectivity AMP ConnectorsIn Stock: 28513-106506-2 Datasheet

MFR RecommendedRFQ

6-106506-2

TE Connectivity AMP ConnectorsIn Stock: 7926-106506-2 Datasheet

MFR RecommendedRFQ

8-106506-2

TE Connectivity AMP ConnectorsIn Stock: 11948-106506-2 Datasheet

MFR RecommendedRFQ

D15S13A4GV00LF

Amphenol ICC (FCI)In Stock: 1994D15S13A4GV00LF Datasheet

MFR RecommendedRFQ

D15S13A4GX00LF

Amphenol ICC (FCI)In Stock: 2442D15S13A4GX00LF Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the HARTING 09662537613 are qualified based on the following critical parameters that must match or exceed the main part specifications:

Mandatory Matching Parameters:

• Connector type: D-Sub receptacle, female sockets
• Number of positions: 15
• Number of rows: 2
• Shell size and layout: 2 (DA, A)
• Mounting type: Through hole, right angle
• Termination method: Solder
• Flange feature: Mating side, female screwlock (4-40)
• Material flammability rating: UL94 V-0
• Moisture sensitivity level: 1 (Unlimited)

Performance Parameters (Must Meet or Exceed):

• Current rating: Minimum 6.5A
• Operating temperature range: Minimum -55°C to 125°C
• Backset spacing: 0.409" (10.40mm) ±0.003"

Five substitute parts meet these criteria across two manufacturers: TE Connectivity AMP Connectors (AMPLIMITE HD-20 series) and Amphenol ICC (FCI) (Delta D series).

Parameter Comparison

Engineering Selection Recommendations

TE Connectivity AMPLIMITE HD-20 Series (3-106506-2, 6-106506-2, 8-106506-2): These parts are suitable substitutes with the following considerations. The TE parts operate at -55°C to 105°C, which is 20°C lower than the HARTING part at the upper temperature limit. The current rating is 6A, which is 0.5A lower than the HARTING specification. Backset spacing is 0.406" (10.30mm), a 0.003" deviation from the HARTING 0.409" specification. All three TE variants are RoHS compliant and carry UL94 V-0 flammability ratings. The primary distinction among the three TE parts is packaging (tray for 3-106506-2, bulk for 6-106506-2 and 8-106506-2) and flange feature configuration (mating side screwlock for 3-106506-2 and 8-106506-2, housing/shell for 6-106506-2).

Amphenol ICC (FCI) Delta D Series (D15S13A4GV00LF, D15S13A4GX00LF): These parts provide the closest electrical and thermal performance match to the HARTING 09662537613. Both operate across the full -55°C to 125°C temperature range and feature identical backset spacing of 0.409" (10.40mm). The current rating is specified as 5A per contact, which is lower than the HARTING 6.5A rating. Both Amphenol parts are RoHS compliant with UL94 V-0 flammability ratings. The distinction between the two Amphenol variants is the flange feature: D15S13A4GV00LF has mating side female screwlock, while D15S13A4GX00LF has housing/shell mounting.

All substitute parts are active products with current manufacturing status and adequate inventory availability.

Frequently Asked Questions (FAQ)

Q: Can I use a TE Connectivity part as a direct replacement for the HARTING 09662537613?

A: TE Connectivity AMPLIMITE HD-20 series parts (3-106506-2, 6-106506-2, 8-106506-2) are mechanically and electrically compatible substitutes. However, note that the TE parts have a reduced upper operating temperature limit of 105°C compared to the HARTING 125°C specification, and a slightly lower current rating of 6A versus 6.5A. Backset spacing differs by 0.003" (0.10mm). These differences are within typical connector tolerance ranges for most applications.

Q: What is the difference between the three TE Connectivity part numbers?

A: The three TE parts (3-106506-2, 6-106506-2, 8-106506-2) share identical electrical and thermal specifications but differ in packaging and flange configuration. Part 3-106506-2 is supplied in tray packaging with mating side female screwlock. Parts 6-106506-2 and 8-106506-2 are supplied in bulk packaging; 6-106506-2 features housing/shell mounting while 8-106506-2 has mating side female screwlock.

Q: How do the Amphenol Delta D parts compare to the HARTING connector?

A: The Amphenol D15S13A4GV00LF and D15S13A4GX00LF parts match the HARTING operating temperature range (-55°C to 125°C) and backset spacing (0.409"). The primary difference is the current rating specification of 5A per contact versus the HARTING 6.5A. Both Amphenol parts include board lock and mounting bracket features. The two Amphenol variants differ only in flange configuration: D15S13A4GV00LF has mating side female screwlock, while D15S13A4GX00LF has housing/shell mounting.

Q: Are all substitute parts RoHS compliant?

A: Yes, all five substitute parts are RoHS compliant. The HARTING 09662537613 is ROHS3 compliant, while the TE and Amphenol substitutes carry RoHS compliance certifications suitable for equivalent applications.

Q: What packaging options are available for these substitute parts?

A: TE Connectivity 3-106506-2 is supplied in tray packaging. TE Connectivity 6-106506-2 and 8-106506-2 are supplied in bulk packaging. Amphenol D15S13A4GV00LF and D15S13A4GX00LF are supplied in tray packaging. Packaging selection should align with assembly process requirements and inventory management practices.

Q: Can I mix substitute parts in the same application?

A: All five substitute parts are mechanically and electrically compatible with the HARTING 09662537613 within the specified parameter tolerances. However, design consistency and supply chain management typically favor standardizing on a single part number per application to ensure uniform performance and simplify procurement.