HARTING 09662527611 D-Sub Receptacle Connector - Equivalent & Substitute Parts

Part Overview

The HARTING 09662527611 is a 15-position D-Sub receptacle connector with female sockets, configured for through-hole right-angle solder termination. This connector is classified as active product status and is RoHS3 compliant. D-Sub receptacle connectors are essential interface components in applications requiring standardized signal transmission, data communication, and power distribution across industrial, aerospace, and defense systems. Substitute parts are identified when equivalent electrical and mechanical parameters align with the original specification, enabling component interchangeability for procurement flexibility, inventory optimization, or supply chain continuity.

Substiute Parts

09662527611

HARTINGIn Stock: 97709662527611 Datasheet

Current PartRFQ

1218434-2

TE Connectivity Aerospace, Defense and MarineIn Stock: 9821218434-2 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the HARTING 09662527611 is determined by strict alignment of the following core parameters:

• Connector type must be receptacle with female sockets
• Position count must be 15
• Row configuration must be 2 rows
• Shell size and layout must be 2 (DA, A)
• Mounting type must be through-hole, right-angle configuration
• Termination method must be solder
• Operating temperature range must encompass -55°C to 125°C minimum
• Shell material must be steel
• Contact type must be signal

The substitute part TE Connectivity 1218434-2 satisfies all mandatory substitution criteria. Both connectors share identical mechanical interfaces, electrical contact configurations, and thermal operating specifications, enabling direct functional replacement in applications where the original part is unavailable or where supply chain alternatives are required.

Parameter Comparison

Engineering Selection Recommendations

Both the HARTING 09662527611 and TE Connectivity 1218434-2 maintain active product status and share identical mechanical and electrical interface specifications for the 15-position D-Sub receptacle configuration. The primary differentiation factors are:

Current rating: The HARTING part supports 6.5A, while the TE Connectivity substitute supports 5A. Selection should be based on actual circuit current requirements.

Backset spacing: The HARTING part specifies 0.409" (10.40mm), while the TE Connectivity part specifies 0.318" (8.08mm). This dimensional difference may affect PCB layout compatibility and should be verified against board design specifications.

Compliance: The HARTING part is RoHS3 compliant, while the TE Connectivity part is RoHS non-compliant. Regulatory requirements for the end application must determine compliance necessity.

Both parts are suitable for applications operating within the -55°C to 125°C temperature range and are classified as active products with ongoing manufacturer support.

Frequently Asked Questions (FAQ)

Q: Can the TE Connectivity 1218434-2 be used as a direct replacement for the HARTING 09662527611?

A: Functional substitution is possible when the application current requirement does not exceed 5A and backset spacing of 0.318" (8.08mm) is compatible with the PCB layout. Both connectors share identical position count, row configuration, shell size, mounting type, and termination method. Verify current and dimensional requirements before implementation.

Q: What is the significance of the different backset spacing values?

A: Backset spacing defines the distance from the connector mounting face to the contact engagement plane. The HARTING part at 0.409" (10.40mm) and the TE Connectivity part at 0.318" (8.08mm) represent different mechanical designs. PCB hole patterns and mating connector depths must be verified for compatibility.

Q: Does RoHS compliance affect substitution eligibility?

A: RoHS compliance is a regulatory requirement determined by the end application and target market. The HARTING part is RoHS3 compliant, while the TE Connectivity part is non-compliant. Applications subject to RoHS regulations must use the compliant part. Non-regulated applications may use either part based on other technical criteria.

Q: Are the current ratings interchangeable?

A: No. The HARTING part is rated for 6.5A, while the TE Connectivity part is rated for 5A. The substitute part must not be used in applications requiring current capacity exceeding 5A. Verify actual circuit current draw before selecting the substitute.

Q: What packaging differences exist between these parts?

A: The HARTING part is supplied in tray packaging, while the TE Connectivity substitute is supplied in bulk packaging. Packaging format does not affect electrical or mechanical compatibility but may influence inventory handling and procurement processes.