0830CDMCCDS-1R0MC Equivalent & Substitute Parts

Part Overview

The 0830CDMCCDS-1R0MC is a 1 µH shielded molded inductor manufactured by Sumida America Components Inc., rated for 17 A continuous current with a maximum DC resistance of 5.4 mOhm. This surface mount component operates across the industrial temperature range of -55°C to 125°C and is ROHS3 compliant. The part is currently active in production with 1619 units in stock. Substitute parts are identified when equivalent electrical specifications and mechanical compatibility allow direct replacement in circuit applications.

Substiute Parts

0830CDMCCDS-1R0MC

Sumida America Components Inc.In Stock: 17120830CDMCCDS-1R0MC Datasheet

Current PartRFQ

IHLP3232CZER1R0M11

Vishay DaleIn Stock: 1917IHLP3232CZER1R0M11 Datasheet

DirectRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the 0830CDMCCDS-1R0MC is determined by the following critical parameters:

Inductance value must match at 1 µH with ±20% tolerance specification. Current rating must support the application requirement; the substitute must maintain a continuous current rating of 16 A or higher. DC resistance must not exceed 6.49 mOhm to ensure thermal performance within acceptable limits. Shielding type must remain shielded to maintain electromagnetic compatibility. Operating temperature range must encompass -55°C to 125°C. Surface mount packaging and nonstandard case dimensions must be compatible with the PCB layout. RoHS3 compliance and MSL 1 rating must be maintained for supply chain and manufacturing process compatibility.

Parameter Comparison

Engineering Selection Recommendations

The IHLP3232CZER1R0M11 qualifies as a substitute for the 0830CDMCCDS-1R0MC based on matching inductance value, tolerance, shielding configuration, and operating temperature range. Both components maintain ROHS3 compliance and MSL 1 rating, ensuring compatibility with standard manufacturing and supply chain processes.

The substitute exhibits a 1 A reduction in continuous current rating (16 A versus 17 A) and a 2.8 A reduction in saturation current (14.8 A versus 17 A). The DC resistance increases by 1.09 mOhm (6.49 mOhm versus 5.4 mOhm). Physical dimensions increase by 0.54 mm in length and 0.38 mm in width, while height remains constant at 3.00 mm maximum.

Selection between these parts depends on application current requirements and PCB layout constraints. Applications requiring the full 17 A continuous rating or 17 A saturation current must use the primary part. Applications with current demands at or below 16 A continuous and 14.8 A saturation may use the substitute, provided the slightly higher DC resistance is acceptable for thermal budget calculations.

Frequently Asked Questions (FAQ)

Q: Can the IHLP3232CZER1R0M11 replace the 0830CDMCCDS-1R0MC in all applications?

A: Substitution is valid only when application current requirements do not exceed 16 A continuous and 14.8 A saturation. The primary part supports higher current ratings and lower DC resistance.

Q: What is the impact of the increased DC resistance in the substitute part?

A: The IHLP3232CZER1R0M11 exhibits 1.09 mOhm higher DC resistance. This increases resistive losses and heat generation proportionally to the square of the current. Thermal analysis must confirm acceptability for the specific application.

Q: Are the physical dimension differences significant for PCB layout?

A: The substitute is 0.54 mm longer and 0.38 mm wider than the primary part. PCB footprints must accommodate these larger dimensions. Height remains identical at 3.00 mm maximum.

Q: Do both parts meet the same compliance and environmental standards?

A: Yes. Both components are ROHS3 compliant, carry MSL 1 rating, and operate across -55°C to 125°C. Supply chain and manufacturing process compatibility is maintained.

Q: What is the inductance frequency test condition for both parts?

A: Both the 0830CDMCCDS-1R0MC and IHLP3232CZER1R0M11 are tested at 100 kHz for inductance value verification.