Molex 0395345113 Terminal Block Plug – Equivalent & Substitute Parts

Part Overview

The Molex 0395345113 is a 13-position terminal block plug with female sockets, 0.200" (5.08mm) pitch, designed for 180° free-hanging in-line applications. This component is part of the Eurostyle ESE 39534 series and is rated for 18 A at 300 V per UL standards. The part is currently active in production with 811 units in stock. Substitute parts are identified when equivalent electrical and mechanical parameters align with application requirements, enabling component sourcing flexibility and supply chain continuity.

Substiute Parts

0395345113

MolexIn Stock: 8520395345113 Datasheet

Current PartRFQ

1-796634-3

TE Connectivity AMP ConnectorsIn Stock: 6841-796634-3 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the Molex 0395345113 is determined by strict alignment of the following critical parameters:

• Position Count & Pitch: 13 positions at 0.200" (5.08mm) spacing (non-negotiable for mechanical fit)
• Connector Type: Plug with female sockets, 180° wire entry orientation
• Termination Method: Screw-based rising cage clamp technology
• Electrical Ratings: Current capacity (minimum 15 A), voltage rating (300 V), and wire gauge compatibility (12-30 AWG)
• Housing Material & Flammability: Polyamide (PA66) construction with UL94 V-0 rating
• Compliance: ROHS3 compliance and active product status

The substitute part TE Connectivity AMP Connectors 1-796634-3 meets these criteria with documented equivalence in position count, pitch, connector type, termination style, and compliance certifications. Minor parameter variations (current rating 15 A vs. 18 A, operating temperature range -40°C to 110°C vs. 115°C, and screw torque specification) remain within acceptable tolerance for most applications but must be evaluated against specific circuit requirements.

Parameter Comparison

Engineering Selection Recommendations

Both the Molex 0395345113 and TE Connectivity 1-796634-3 are active products with ROHS3 compliance and UL94 V-0 flammability certification. Selection between these parts should be based on application-specific current requirements:

• Molex 0395345113: Select when circuit design requires the full 18 A current capacity or when operating temperatures approach 115°C.
• TE Connectivity 1-796634-3: Acceptable for applications with maximum current draw of 15 A and operating temperatures not exceeding 110°C. This part includes retention latches on the non-wire side, which may provide additional mechanical security in certain mounting configurations.

Both parts support identical wire gauge ranges (12-30 AWG) and maintain equivalent electrical isolation and safety ratings. Mechanical fit and mating compatibility are assured due to identical position count, pitch, and connector geometry.

Frequently Asked Questions (FAQ)

Q: Can the TE Connectivity 1-796634-3 be used as a direct replacement for the Molex 0395345113?

A: Direct substitution is valid when circuit current requirements do not exceed 15 A and operating temperatures remain below 110°C. The identical pitch (5.08mm), position count (13), connector type, and termination method ensure mechanical and electrical compatibility within these parameter limits.

Q: What is the significance of the 3 A current rating difference?

A: The Molex part is rated for 18 A while the TE Connectivity part is rated for 15 A. This difference reflects the maximum continuous current each connector can safely handle. Applications drawing more than 15 A require the Molex part to maintain design margin and thermal safety.

Q: Are there differences in wire entry or mounting orientation?

A: No. Both parts feature 180° free-hanging in-line wire entry and identical mounting configuration. They are mechanically interchangeable in terms of installation geometry.

Q: What does the retention latch feature on the TE Connectivity part provide?

A: The TE Connectivity 1-796634-3 includes retention latches on the non-wire side. This feature provides additional mechanical retention of the mated connector pair, reducing the risk of accidental disconnection in vibration-prone or high-movement environments.

Q: Are both parts compliant with current environmental and safety standards?

A: Yes. Both the Molex 0395345113 and TE Connectivity 1-796634-3 are ROHS3 compliant, carry UL94 V-0 flammability ratings, and are classified as active products with ongoing manufacturer support.

Q: What is the difference in screw torque specifications?

A: The Molex part specifies 0.56 Nm (5.0 Lb-In) torque, while the TE Connectivity part specifies 0.79 Nm (7.0 Lb-In). Both values fall within acceptable ranges for M3 screw fastening. Follow the torque specification of the part being installed to ensure proper wire termination without over-tightening.